manualshive.com logo in svg

MotorGuide TOUR 109, Руководство по эксплуатации, техническому обслуживанию, установке и гарантии

Поделиться
Скачать
MotorGuide TOUR 109 Скачать руководство пользователя страница 45

IMPORTANT: GPS signal strength may vary, depending on satellite reception.

This can affect GPS performance.

a -

Manual mode

b -

#1 button

1.

a.

If performing the compass calibration with the boat in the water:

locate a suitable area clear of obstructions to navigation (both above

and below the waterline) to perform the compass calibration.

b.

If performing the compass calibration with the boat on the trailer:

locate a suitable area clear of obstructions to perform the compass

calibration.

2. Deploy the trolling motor. Adjust the motor height so that the bottom of the

head is 15.2 cm (6 in.) above the depth collar and the motor. If performing

the compass calibration with the boat in the water, verify that you are in a

location where your trolling motor and primary propulsion engine will not

hit bottom or other obstructions.

3. Press and hold the 

manual mode

 button, then press 

1

, 

1

, 

1

. The trolling

motor will emit three ascending‑tone beeps and the GPS status indicator

light will turn off.

4.

a.

If performing the compass calibration with the boat in the water:

use the primary propulsion engine to slowly drive the boat in two

complete circles.

b.

If performing the compass calibration with the boat on the trailer:

tow the boat in two complete circles.

5. Two beeps will occur when very close to completing the second circle.

The GPS status indicator light will turn on and a beep will occur, signalling

a successful compass calibration.

53737

b

a

TROLLING MOTOR INSTALLATION AND OPERATION

eng

39

  

Содержание TOUR 109













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды