manualshive.com logo in svg

MotorGuide TOUR 109, Руководство по эксплуатации, техническому обслуживанию, установке и гарантии

Поделиться
Скачать
MotorGuide TOUR 109 Скачать руководство пользователя страница 28

6. Push the pedal into the full heel down position and install the rear screw

on the foot pedal.

a -

Rear screw

b -

Front screws (2)

Bounce Buster Installation

1. Place the trolling motor in the stowed position.
2. Remove the bounce buster from the mounting accessory kit.

!

 CAUTION

Avoid injury from parts flying into the passenger compartment of the boat. If

the  bounce  buster  is  not  correctly  installed,  the  trolling  motor  can

inadvertently deploy, which  at  planning  speed could result  in  catastrophic

failure  of  the  trolling  motor.  Check  that  the  stow  latch  fully  engages  after

installation of the bounce buster.

3. Measure the distance between the boat deck and the outside surface of

the mounting bracket.

a -

Distance between the boat deck and the

outside surface of the mounting bracket.

4. Add 6.35 mm (1/4 in.) to the measured length (distance between the boat

deck and the outside surface of the mounting bracket) taken in the

previous step.

a

b

70278

70125

a

TROLLING MOTOR INSTALLATION AND OPERATION

  

22

eng

Содержание TOUR 109













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды