MotorGuide TOUR 109 Скачать руководство пользователя страница 30

Страница: 30 / 76

NOTE: Install the steering system if removed. Refer to

Installing the Steering

System on the Mount

10. Stow the trolling motor.

70020

11. Adjust the boot end of the bounce buster by removing the rubber boot,

loosen the jam nut by turning the screw counter clockwise to the desired

length.

12. Tighten the jam nut to the base of the bounce buster followed by a

clockwise turn.

13. Replace the rubber boot.

a -

Bounce buster

b -

Jam nut

c -

Screw

d -

Rubber boot

14. Verify in the stowed position that the stow latch is engaged by lifting up on

the 360 breakaway without the use of the stow/deploy handle. If the stow

latch is engaged, the mount will not release. If mount releases, repeat

Step 9 until Step 10 can be verified.

Installing the Gas Spring

1. Remove the gas spring from the Accessory Kit located in the packaging.
2. Rotate the motor into the stowed position until the ball end studs align

with the gas spring end fittings.

IMPORTANT: Do not install the gas spring with the rod end up. This can result

in premature gas spring failure.

3. Push or squeeze the piston end fitting of the gas spring onto the ball stud

located on the inner arm of the mount.

c d

70138

TROLLING MOTOR INSTALLATION AND OPERATION

eng

Содержание TOUR 109













































































Результаты поиска

Содержание TOUR 109

Отзывы:

Бренды по названию

Популярные бренды

MotorGuide TOUR 109, Руководство по эксплуатации, техническому обслуживанию, установке и гарантии

Результаты поиска

Содержание TOUR 109

Отзывы:

Бренды по названию

Популярные бренды