background image

AGITO

AGITO User Manual OS 5.0 Nova

50 - Operation

www.Motion-Impossible.com

 

»

RF MODULE & COMMUNICATIONS SETTINGS

ALWAYS ENSURE THAT THE POWER SETTINGS ARE LEGAL IN THE TERRITORY OF OPERATION.

AS WITH ALL RF SYSTEMS, LINE OF SIGHT BETWEEN TRANSMITTER AND RECEIVER IS 

ESSENTIAL. ALWAYS ENSURE THAT THE ANTENNAS ARE FREE FROM OBSTRUCTIONS.

The system comes with a 2.4 GHz (100mW) module as standard.  The RF module is fixed in place using a single locking screw, simply 
unscrew this to remove the RF and swap for other RF modules (sold separately) when required. Always check that factory paired modules 
are used.

 

»

CHANGING SETTINGS

 

🌐

https://motion-impossible.com/how-to-videos/

ALWAYS ENSURE FRESH BATTERIES ARE INSTALLED AND NEVER TURN OFF THE AGITO 

MASTER CONTROLLER AND/OR CORE WHILST CHANGING RF SETTINGS, DOING SO MAY 

REQUIRE THE RF MODULES BEING RETURNED TO A SERVICE CENTRE TO BE RESET.

To change the settings of the AGITO RF modules, navigate to the Top Level Menu by turning on the MASTER Controller or applying a long 
press to the MENU button. Scroll down and select SYSTEM MENU, then navigate to the RF COMMS menu, see “” on page 18.

The AGITO system will push settings changes from the MASTER Controller to the CORE, once a setting has been selected and mode 
change transmitted, the RF connection will shut down for up to 3 seconds whilst the modules are configured. The RF system will then 
automatically restart and check that communication has been re-established. If an error occurs and the MASTER Controller is unable to 
connect to the CORE then the modules will revert to the previous setting after 10 seconds. 

If the CORE is unable to connect to the MASTER Controller, the main power button will flash slowly.

 

»

RF POWER

By default the system is set to 100mW, this is the legal limit in most countries and territories around the world. It is vital that the owner 
of the system ensures that all operators know the legal power limits for the area of operation. This menu can then be used to adjust the 
Transmission Power of the modules to ensure it remains at or below the legal limit.

 

»

RF FORWARD ERROR CORRECTION (FEC)

This feature enables a technique for controlling errors in data transmission in noisy communication environments without the need for 
multiple retransmissions. 

If you are experiencing data-loss or restricted range, ensure that FEC is enabled and that you are using the maximum power that is legal 
in your territory of operation.

 

»

3RD PARTY RF OPTIONS

Using the Data Pass-through module it is possible to use 3rd Party RF solutions including Silvus TriCaster or DTC NetNode/Solo. Please 
contact support for more information.

 

»

WIRED CONTROL

AGITO can be controlled via serial RS232 data using the optional Data Pass-through modules. Serial data has a limited range, therefore for 
longer cable runs or more complex installations MI recommend LANTRONIX Serial to IP converters which can be purchased separately. 

Please contact support if you require more information

Содержание AGITO






















































































Отзывы: