Morgana DIGIFOLD Скачать руководство пользователя страница 10

Страница: 10 / 40

Accessing Menus.

Main Menu.

The mains switch on the machine must be off.

Set the

to its mid position and then turn the mains switch on.

The

functions can then be accessed by turning the

clockwise or anti-clockwise as shown.

Set-up Switch

Main Menu

Setting Dial

CrEES

on / oF = crease on or off

FoLd

on / oF = fold on or off

dELrY

on / oF = delivery on or off

SEt

PoS / FoLd = set by position or set by fold

bAt = batch

.00 .00 = roller gap

Sub-menus.

Set-up switch

Setting Dial

To access the sub-menus flick the

to the down position and turn the

clockwise or anti-clockwise.

1 Cr = crease position 1

9 Cr = crease position 9

= fold 1 position

= fold 2 position

rPoS = delivery roller position

Shin = shingle (amount delivery wheel turns)

rESEt = reset

Sub-Menu in Set by

mode (set by position).

PoS

tYPE

L = type of fold i.e. L = letter fold

Len 100 = paper length
PAPEr 3 = type of paper (0= light 3 = heavy)

Cr1

0.0 = crease 1 position

rPoS 150 = delivery roller position
Shin

41 = shingle (amount delivery wheel turns)

Cr2

0.0 = crease 2 position

Sub-Menu in Set by

mode (set by fold)

FoLd

0.0 = fold 1 position

0.0 = fold 2 position

Clockwise

Anti-clockwise

Clockwise

Anti-clockwise

Clockwise

Anti-clockwise

Operating the Digifold

Page 10

CREASING / FOLDING

F_cLr

on / oF = fold blade clear of paper to reduce the possibility of marking or

scratching sensitive paper, on or off

Содержание DIGIFOLD









































Результаты поиска

Содержание DIGIFOLD

Отзывы:

Похожие инструкции для DIGIFOLD

Бренды по названию

Популярные бренды

Morgana DIGIFOLD, Руководство по эксплуатации

Результаты поиска

Содержание DIGIFOLD

Отзывы:

Похожие инструкции для DIGIFOLD

Бренды по названию

Популярные бренды