Mopar K6860899 Скачать руководство пользователя страница 57

Страница: 57 / 121

32. Position the quarter trim panel in the vehicle.

33. If equipped, connect the wire harness connector to the

power outlet.

34. Position the ﬂange on the quarter trim panel into the

seal ditch and secure the bottom clip ﬁrst and then the
middle clip.

35. Align the two fastener holes in the quarter trim panel

with the two fastener holes in the quarter panel and
engage the retaining tabs that secure the quarter trim
panel to the quarter panel.

36. Install the two screws that secure the quarter trim

panel to the quarter panel.

37. Position the load ﬂoor in the vehicle. Route the twisted

pair wire harness (2) through the bottom of the ﬂoor
and connect the harness to the WiFi Router connec
tor.

38. Install the two nuts that secure the load ﬂoor to the

ﬂoor panel.

39. Using the supplied selftapping screws, secure the

WiFi Router bracket (1) to the load ﬂoor.

40. Install the Dpillar trim panel. Position the locating tabs

on the bottom of the Dpillar trim panel into the slots
in the top of the quarter trim panel.

41. Align the retaining tabs on the Dpillar trim panel with

the retaining clips in the Dpillar and engage the re
taining tabs that secure the trim panel to the Dpillar.

Oct 16, 2009

K6860899 Rev. 1

Содержание K6860899


























































































































Результаты поиска

Содержание K6860899

Отзывы:

Mopar K6860899, Инструкция по эксплуатации, Страница: 57 / 121

Результаты поиска

Содержание K6860899

Отзывы: