Mopar K6860899 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 121

Mopar K6860899 Скачать руководство пользователя страница 40

1

WIFI ROUTER

DAKOTA

PROCEDURE STEPS:

1.

Disconnect and isolate the negative battery cable.

WARNING: To avoid personal injury or death, when handling a seat belt tensioner retractor, exercise proper care
to keep ﬁngers out from under the retractor cover and away from the seat belt webbing where it exits from the
retractor cover. Failure to follow these instructions may result in possible serious or fatal injury.

WARNING: To avoid serious or fatal injury on vehicles equipped with airbags, disable the Supplemental Restraint
System (SRS) before attempting any steering wheel, steering column, airbag, seat belt tensioner, impact sensor,
or instrument panel component diagnosis or service. Disconnect and isolate the battery negative (ground) ca
ble, then wait two minutes for the system capacitor to discharge before performing further diagnosis or service.
This is the only sure way to disable the SRS. Failure to take the proper precautions could result in accidental
airbag deployment.
CLUB CAB

2.

Remove the two plastic pushpin retainers (2) that se
cure the outer front seat belt retractor cover (1) to the
outer front seat belt retractor (3).

3.

Raise the retractor cover upward to disengage the two
locator pins on the inside top of the inboard retractor
cover from the locator holes in the top of the retractor.

4.

Spread the bottom of the inboard (1) and outboard (3)
retractor cover halves apart and disengage the snaps
located at the top of the cover halves and remove the
cover halves.

Oct 16, 2009

K6860899 Rev. 1

«
...
38
39
40
41
42
...
»

Содержание K6860899


























































































































Отзывы:

Нет отзывов