Mopar K6860899 Скачать руководство пользователя страница 5

Страница: 5 / 121

20. Install the WiFi router cradle (2) to the rear cab trim

panel (1) with the provided materials.

21. Make a small cut in the rear cab trim panel and route

the WiFi router connector through

22. Place the rear cab trim panel into position in the vehi

cle.

23. Connect the wire harness to the WiFi router connec

tor.

24. Route the wire harness down the back of the rear

panel to the door sill.

25. Firmly seat the rear panel and install the utility hooks

to the rear panel.

26. Continue to route the wire harness along the passen

ger side, under the glove box opening and behind the
center stack and cut to the proper length.

27. Locate the cigarette lighter outlet wiring harness.

28. Cut each wire and remove 13 mm (0.5 in.) of insula

tion from each wire that needs to be soldered/spliced.

29. Place a piece of supplied adhesive lined heat shrink

tubing on one side of each cut wire. Insure the tubing
will be long enough to cover and seal the entire sol
dered area.

CAUTION: Do not use acid core solder.

30. Solder the supplied fused pigtail to WiFi power har

ness power wire (RD/LG).

31. Place the strands of the power side wires overlapping

each other inside of the splice clip (1).

Oct 16, 2009

K6860899 Rev. 1

Содержание K6860899


























































































































Результаты поиска

Содержание K6860899

Отзывы:

Mopar K6860899, Инструкция по эксплуатации, Страница: 5 / 121

Результаты поиска

Содержание K6860899

Отзывы: