manualshive.com logo in svg

Mopar K6860899, Инструкция по эксплуатации, Страница: 37 / 121

Поделиться
Скачать
Mopar K6860899 Скачать руководство пользователя страница 37

2

9.

Install the Wi­Fi router bracket (1) under the passen­
ger seat with the provided materials.

10. Connect the wire harness to the Wi­Fi router bracket

harness.

11. Route the Wi­Fi power harness under the center con­

sole to the shifter housing and cut the harness to the
proper length. Ensure the harness is tucked under the
center console to minimize visible wire.

12. Locate the cigarette lighter outlet wiring harness.

13. Cut each wire and remove 13 mm (0.5 in.) of insula­

tion from each wire that needs to be soldered/spliced.

14. Place a piece of supplied adhesive lined heat shrink

tubing on one side of each cut wire. Insure the tubing
will be long enough to cover and seal the entire sol­
dered area.

CAUTION: Do not use acid core solder.

15. Solder the supplied fused pigtail to Wi­Fi power har­

ness power wire.

16. Place the strands of the power side wires overlapping

each other inside of the splice clip (1).

Oct 16, 2009

K6860899 Rev. 1

Содержание K6860899


























































































































Отзывы:

Нет отзывов