Mopar K6860899 Скачать руководство пользователя страница 54

Страница: 54 / 121

NOTE: Make sure enough wire length is supplied to go into the load ﬂoor where the WiFi router (1) will be
located.

17. Route and secure the WiFi power harness from rear

quarter panel, along the passenger side and under
neath the door sill scuff plate.

18. Route and secure the power harness under the glove

box and behind the center stack.

NOTE: Do not use the power outlet wiring for the WiFi
Router.

19. Locate the cigarette lighter outlet wiring harness.

20. Splice the supplied fused pigtail (2) into the cigarette

lighter power wire and in series with the WiFi power
harness.

21. Remove 13 mm (0.5 in.) of insulation from each wire

that needs to be spliced.

22. Place a piece of adhesive lined heat shrink tubing on

one side of the wire. Make sure the tubing will be long
enough to cover and seal the entire repair area.

23. Place the strands of wire overlapping each other in

side of the splice clip (1).

Oct 16, 2009

K6860899 Rev. 1

Содержание K6860899


























































































































Результаты поиска

Содержание K6860899

Отзывы:

Mopar K6860899, Инструкция по эксплуатации, Страница: 54 / 121

Результаты поиска

Содержание K6860899

Отзывы: