Mopar K6860899 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 121

Mopar K6860899 Скачать руководство пользователя страница 2

1

WIFI ROUTER, REGULAR CAB

DODGE RAMREGULAR CAB

PROCEDURE STEPS:

NOTE: Using a test light, verify the cigarette lighter outlet being used is ignition switched. Power must not be
supplied with the ignition in the OFF position.

1.

Disconnect and isolate the battery negative cable.

2.

Using a trim stick C4755 or equivalent, disengage the
retaining tabs and remove the lower bezel panel (1).

3.

Remove the two lower screws securing the cup holder
to the IP.

4.

Fold the cup holder down and lower the cup holder (2)
close out panel by depressing the tab at the top of the
panel.

5.

Remove the two screws from behind the close out and
remove the cup holder.

6.

Using trim stick C4755 or equivalent, disengage the
retaining tabs and disconnect the power outlet electri
cal connectors.

7.

Remove the lower IP surround from the vehicle.

8.

Open the glove box (1).

9.

Release the two glove box stops (2) and lower the
glove box downward past the stops.

10. Disengage the glove box hinges from the instrument

panel and remove the glove box.

Oct 16, 2009

K6860899 Rev. 1

«
1
2
3
4
...
»

Содержание K6860899


























































































































Отзывы:

Нет отзывов