Moore Industries TDZ, Руководство по установке

Страница: 14 / 32

10 The Interface Solution Experts
THZ & TDZ
Installing the Configuration Software
Refer to Table 5 for the equipment needed.
1. Insert the diskette labeled “TDZ/THZ
Configuration Program Installation Disk 1 of 3”
into the floppy drive of the PC.
2. In Windows
®
95/98/NT, go to the “Start” menu,
and access “Settings”, then “Control Panel”,
and finally “Add/Remove Programs”.
3. Click “Install” and follow the instructions on
the screen.
Note:
Two utility disks are also provided with your PC Pro-
gram. These are for users of Windows 95 with
Internet Explorer 3.0x, or Windows NT.
Do not install these if you are using Windows 98.
Table 5. Assembling the equipment needed to configure the THZ or TDZ
Variable Input Simulator for Thermocouple,
RTD, Millivolt, Potentiometer, or Decade
Resistance Box
Power Supply
Precision Load Resistor
Multimeter (optional)
Personal Computer
(Required only if
using a PC for setup)
HART Modem Cable
(Required only if using a PC)
Moore Industries PC
Configuration Software
(Required only if using a PC)
HART Communicator
(Required only if NOT using a PC)
Variable; Accurate to ±0.05% of unit span
24Vdc, ±10%
250 ohms, ±0.01% HART specifies that total loop resistance is to be maintained
between 250 ohms and 1100 ohms.
Accurate to ±0.025% of span; e.g., Fluke Model 87
80386-based(or faster) IBM PC, or 100% compatible;
1.44MB floppy diskette drive
4Mb free RAM; 8Mb recommended; 20Mb free disk space on hard drive
(More RAM & hard disk space is required for Windows 98 or NT)
Microsoft Windows
®
95, 98, or NT
Internet Explorer 3.0+ (required for HelpMap)
1 (one) serial port (COM 1, 2, 3, or 4) set to 4800 baud, no parity, 8 data bits, and 1 stop bit
Moore Industries part number 803-048-26, or equivalent
Version 1.0 or greater, successfully installed to the hard drive
Fisher-Rosemount Model 275 or equivalent
Device Specifications
Connecting the THZ or TDZ to the PC
To set any of the options, you must first connect
the unit to the PC. The THZ hockey-puck, THZ
DIN, THZ DH, and TDZ all have the same terminal
designations, and all can be setup using the
connections shown in Figure 10, page 12.
Establish a simple current loop for the transmitter
by connecting a 24-volt power supply, a 250
Ω
resistor, and the transmitter in series. See Table 5
below for information on the necessary equipment.
Then connect a suitable HART modem. Connect
the RS-232 end of the modem to the PC’s COM
port, then connect the HART output end of the
modem (two hookup wires) across the transmitter
or the load resistor.
This makes it easy to create a set of operating pa-
rameters, save them to disk, and download them to
one or more transmitters at a later time.
The THZ or TDZ must be connected to the PC in or-
der to: trim input, trim output, assign a tag, perform a
loop test, receive (via download) a configuration file,
and save the configuration file from the transmitter’s
memory.
Once the Configuration Program is installed on the
PC, the THZ or TDZ can be connected to equipment
to simulate input and monitor output. The user can
then change the transmitter’s operating parameters.
No Transmitter Needed
It is not necessary to connect the transmitter to a PC
to create configuration files using the software. The
Configuration Program can be run without connecting
a transmitter, and
most parameters can be set
without benefit of input from a sensor or transmitter.