Montigo H38DF PRC Скачать руководство пользователя страница 3

Страница: 3 / 44

Page 3

XG0211 - 151126

Indicates a hazardous situation which, if not

avoided, WILL result in death or serious

injury or property damage.

Indicates a hazardous situation which, if not

avoided, COULD result in death or serious

injury or property damage.

Indicates a hazardous situation which, if not

avoided, WILL result in minor or moderate

injury.

Address practices that are important, but

not related to personal injury

DANGER

WARNING

CAUTION

NOTICE

H*38DF PRC Panorama Indoor Gas Fireplace

Safety Alert Key

Introduction

Safety Alerts

INTRODUCTION

Congratulations on your purchase of a Montigo Fireplace.

With over 30 years of experience, Montigo is committed

to providing you with a gas fireplace that is not only a

beautiful addition to your space, but that is also designed

and manufactured to the highest safety, reliability and

engineering standards.

We strongly encourage you to read and carefully follow

the instructions laid out in this Installation, Operation and

Maintenance Manual and retain it for your future reference.

Pay special attention to all cautions, warnings, and notices

throughout this manual intended to ensure your safety.

This manual covers installation, operation and maintenance.

Lighting, operation and care of this fireplace can be easily

performed by the homeowner. All installation and service

work should be performed by a qualified or licensed installer,

plumber or gas fitter as certified by the state, province, region

or governing body where the fireplace is being installed.

Warranty Information

: (See Appendix B)

The Montigo warranty will be voided by, and Montigo disclaims any

responsibility for the following actions:

► Modification of the fireplace and/or components including

Direct-Vent assembly or glass doors.

► Use of any component part not manufactured or approved

by Montigo in combination with this Montigo fireplace system.
► Installation other than as instructed in this manual.

Consult your local Gas Inspection Branch on installation

requirements for factory-built gas fireplaces. Installation & repairs

should be done by a qualified contractor.

This installation, operation and maintenance manual is

applicable to the models described below. Refer to your

rating plate to verify included options. Throughout this

manual instructions are applicable to all models designated

H*38PR*

unless otherwise noted.

MODEL

Natural Gas

Liquid Propane

Gas Rating (BTU hr)

Traditional Burner w/ Logset

Premium Burner w/ Logset

Linear Burner w/ Glass media Accessories

Standing Pilot Ignition

Honeywell HSI Ignition

SIT Electronic Ignition

H38DFPRCN

34,000

H38DFPRCN-F

34,000

H38DFPRCL

X 32,000

H38DFPRCL-F

X 32,000

HL38DFPRCN-F

34,000

HL38DFPRCL-F

X 32,000

HP38DFPRCN-F

34,000

HP38DFPRCL-F

X 32,000

Young children should be carefully supervised when they are

in the same room as the applicance. Toddlers, young children

and others may be susceptible to accidental contact burns. A

physical barrier is recommended if there are at risk individuals

in the house. To restrict access to a fireplace or stove, install

an adjustable safety gate to keep toddles, young children and

other at risk individuals out of the room and away from hot

surfaces.

CAUTION

Содержание H38DF PRC













































Результаты поиска

Содержание H38DF PRC

Отзывы:

Похожие инструкции для H38DF PRC

Бренды по названию

Популярные бренды

Montigo H38DF PRC, Инструкция по установке и обслуживанию

Результаты поиска

Содержание H38DF PRC

Отзывы:

Похожие инструкции для H38DF PRC

Бренды по названию

Популярные бренды