Montigo H38DF PRC Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 44

background image

H*38DF PRC Panorama Indoor Gas Fireplace

Page 31

XG0211 - 151126

Operation

Section:

1. Turn off remote switch.
2. Flip down the lower trim.

3. Turn the switch on the gas control to "Off".
4. Flip up the trim.

1.  STOP! Read the safety information above on this label.
2.  Lift out the lower Horizontal access panel.
3.  Turn switch on the gas control to OFF".
4.  Wait 5 minutes to clear out any gas. If you smell gas,

STOP! Follow "B" in the safety information above on

this label. If you don't smell gas, go to the next step.

5. Turn switch on the gas control to "ON". NOTE: This unit

is equipped with an ignition system that lights the pilot
burner automatically. Do not attempt to light the pilot by
hand.

6. Turn on wall switch.

7. Replace the lower Horizontal access panel.

8. If the fireplace does not operate, follow the instructions

"To Turn Off Gas To Appliance" and call your service
technician or gas supplier.

Honeywell Electronic Ignition

To Turn Off Gas To Appliance:

Lighting Instructions:

Gas Control Switch

Shown in ‘ON’ Position

Gas

Inlet

«
...
29
30
31
32
33
...
»

Содержание H38DF PRC













































Отзывы:

Нет отзывов

Похожие инструкции для H38DF PRC

Бренд: Majestic Страницы: 4

Бренд: Dimplex Страницы: 8

Бренд: Valcourt Страницы: 70

83035033 WW11994

Бренд: UBERHAUS DESIGN Страницы: 11

Бренд: Pacific energy Страницы: 24

Бренд: Paul Agnew Страницы: 104

Бренд: Glow Fire Страницы: 241

Бренд: Style selections Страницы: 33

Бренд: Valor Страницы: 28

Бренд: Range Master Страницы: 11

Бренд: JAYLINE Страницы: 16

Бренд: Bio Flame Страницы: 7

Бренд: Heat&Glo Страницы: 66

Бренд: Vermont Castings Страницы: 12

Бренд: Vermont Castings Страницы: 28

Бренд: Vermont Castings Страницы: 32

Бренд: EdilKamin Страницы: 16

Firebox Deco Series

Бренд: EdilKamin Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды