Montigo H38DF PRC Скачать руководство пользователя страница 12

Страница: 12 / 44

H*38DF PRC Panorama Indoor Gas Fireplace

Page 12

XG0211 - 151126

Installation

12”

2”

12”

Section 3-3:

INSTALLING A WALL MOUNTED DIRECT VENT

TERMINATION

This section applies to installations where the direct vent termi-

nation will be wall mounted.

1). Installation of Termination with built in frame

A Termination with a Built-In Frame is installed during framing of

a structure.

1. Frame the termination opening to 11" x 11".
2. Install exterior sheathing to the structure framing.
3. Fasten the termination to the sheathing using a minimum of

4 screws.

MSR Frame

PTO-4 (5"/8")
Termination

PTO-4F (5"/8")
Termination

Figure 10. Installing a PTO-F termination.

Figure 10a. Installing a PTO termination with the MSR frame.

Figure 10d. Installing the VSS Vinyl Shield.

5). Installation of a termination shield for Vinyl Siding

The VSS Termination shield

is installed when the exterior of a

structure is clad with Vinyl siding. It is placed directly above, and

on-centre with the termination.

2). Installation of termination frame at time of framing

Terminations with a MSR frame allow the installation of the frame

prior to installation of the termination.

1. Frame the termination opening to 12" x 12".

2. Secure the MSR Frame to the exterior sheathing of the structure.
3. Fasten the termination to the MSR Frame using a minimum of

4 screws.

Figure 10b. Installing a PTO termination with the BSR frame.

3). Installation of termination frame at time of framing in Masonry

Terminations with a BSR frame allow the installation of the frame

in masonry prior to the installation of the termination

1. Frame the BSR opening to 12" x 12".
2. Secure the BSR Frame to the exterior sheathing of the structure.

1. Frame the MOSR opening to 12" x 12".
2. Fasten the MOSR frame to the interior side of the studs,

concrete, or finished wall construction using a minimum of 4

screws.

3. Insert the termination into the MOSR frame as shown here,

(

from the inside

) and attach to the MOSR by installing a min.

quantity of 4 bolts into the threaded nuts on the MOSR Frame.

4). Installation of termination from inside structure

A Termination with a MOSR Frame is installed from the inside of

the structure. These are commonly used in high-rise construction.

MOSR Frame

PTO-4 (5"/8")
Termination

Figure 10c. Installing a PTO termination with the MOSR frame.

BSR Frame

11”

Framing

Exterior
Sheathing

Fastening Hardware,
minimum 4-screws

Framing

Exterior
Sheathing

Fastening Hardware,
minimum 4-screws

PTO-4 (5"/8")
Termination

Framing

Exterior
Sheathing

Fastening Hardware,
minimum 4-screws

12”

Fastening Hardware,
minimum 4-screws

Framing, con-
crete or other
materials

Exterior Sheath-
ing, concrete or
other materials

Exterior Vinyl
siding

PTO-4 (5"/8")
Termination

VSS Vinyl shield

Wall mounted Terminations

The following details are some possible configurations for Wall

mounted terminations. See below.

Содержание H38DF PRC













































Результаты поиска

Содержание H38DF PRC

Отзывы:

Похожие инструкции для H38DF PRC

Бренды по названию

Популярные бренды

Montigo H38DF PRC, Инструкция по установке и обслуживанию

Результаты поиска

Содержание H38DF PRC

Отзывы:

Похожие инструкции для H38DF PRC

Бренды по названию

Популярные бренды