Montigo 30FIDLIL-01 Скачать руководство пользователя страница 34

Страница: 34 / 52

XG0523 - 170223

Operation

Initializing the System for the first time

1. Set master override switch to off position.
2. Install four (4) AA batteries into the battery holder.
3. Install three (3) AAA batteries in the back of the remote

control. Note the polarity of batteries and install them as

indicated by the silk screen (+/-) on the holder.

4. Connect AC Power (115 volts, 60 Hz) to fireplace.

Operating the System for the first time

Press SW1 button on the control module. The control module will

beep three (3) times and an amber LED is illuminated to indicate

that the IFC (control board) is ready to synchronize with a remote

control within 10 sec. Push the ON button. The control module

will "beep" four (4) times to indicate transmitter's command is

accepted.
The System is now initialized.

Temperature Indication Display

With the system in the "Off" position, press the Thermostat Key

and the Mode Key at the same time. Look at the LCD screen on

the Remote Control to verify that a C or F is visible to the right of

the Room Temperature display.

Continuous Pilot (CPI) Selection

(Optional)

In cold weather climates, the pilot burner can stay on

continuously to prevent condensation or cold air temperatures

near the fireplace glass. Note, some jurisdictions do no permit

use of continuous pilot system. Check local codes or contact your

Montigo dealer.

With the system in "off" position press the Mode Key, see Figure

8 Sec.10, to index to the CPI mode icon, see Figure 22 Sec.10.

Pressing the Up Arrow Key will activate the Continuous Pilot

Ignition mode (CPI). Pressing the Down Arrow Key will return to

IPI. A single "beep" will confirm the reception of the command.

NOTE:

- Requires CPI/IPI jumper cable installed

Turn On the Fireplace

With the system Off, turn the master override switch to on and

press the On/Off Key on the Remote Control. The Remote Control

display will show some other active Icons on the screen. At the

same time the Control Module will activate the fireplace. A single

"beep" from the Control Module will confirm reception of the

command.

Turn Off the

Fireplace

With the system On, press

the On/Off Key on the

Remote Control. The Remote

Control LCD display will only

show the room temperature.

At the same time the Control

Module will turn off the

fireplace. A single "beep"

from the Receiver confirms

reception of the command.

Figure 9.12

Remote Control display in Fahrenheit & Celsius

Figure 9.12a

Continuous Pilot / Intermittent Pilot Selection

Figure 9.13

Remote Control Display

Содержание 30FIDLIL-01





















































Результаты поиска

Содержание 30FIDLIL-01

Отзывы:

Похожие инструкции для 30FIDLIL-01

Бренды по названию

Популярные бренды

Montigo 30FIDLIL-01, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 30FIDLIL-01

Отзывы:

Похожие инструкции для 30FIDLIL-01

Бренды по названию

Популярные бренды