59
4 . MAINTENANCE AND TROUBLESHOOTING
Your sowing control console is above all an electronic device, which needs to be treated with care. When sowing is
completed, it must be stored in a dry place.
If the cells are dirty, they should be cleaned with a soft brush.
CAUTION
Disconnect the console power supply before performing any welding operation on the tractor or the seeder to
prevent the system from being damaged.
Symptoms
Probable cause
Solution
The console does not
switch on.
-The fuse on the console supply
harness has blown.
-Bad battery connection.
-Battery voltage too low.
-Battery polarity reversed.
-Faulty console.
ec t e fuse f lo n, replace it a ne five mpere
fuse.
f it lo s a ain, c ec t at t e arness is neit er cut nor dama ed,
otherwise call our after-sales department.
ec t at t e lu s are clean and crimped properl
ec t at t e atter volta e is at least volts t er ise,
recharge or replace the battery.
-Connect the wires to the battery properly.
-Contact our after-sales department.
ac of rains alarm
on one row.
-The number of rows programmed
exceeds the number of rows on
the seeder.
-The grain hopper is empty.
-The seeder element sensor is
dirty.
-Faulty sensor or harness.
-Program a number of rows equal to the number of rows of the
seeder on the CS30.
-Fill the hopper of the seeder element concerned with grains.
lean t e sensor it a e i le rus
-Swap the connection of the faulty sensor with a neighbouring
functional sensor and c ec
et er t e pro lem is displaced
or not. If the problem has been displaced, the sensor is faulty.
t er ise, c ec t at t e arness is not dama ed
ac of fertili er on a
row alarm.
-The number of fertilizer rows
programmed exceeds the number
of fertilizer sensors on the seeder.
e fertili er does not o in t e
dispensing hoses.
-Faulty sensor or harness.
- Program a number of fertilizer sensors equal to the number of
fertilizer sensors of the seeder on the CS30.
ec t at t e fertili er tan is not empt and t e oses concerned
are not clogged.
-Swap the connection of the faulty sensor with a neighbouring
functional sensor and c ec
et er t e pro lem is displaced
or not. If the problem has been displaced, the sensor is faulty.
t er ise, c ec t at t e arness is not dama ed
No forward speed
alarm.
-Faulty speed sensor
-Faulty console
- No speed signal arrives at the console although at least one
sensor detects rains passin
ec t e speed sensor and its
wiring
- Contact our after-sales department.
or in speed too
high alarm.
- A limit speed not to
be exceeded has been
programmed in the advanced
menu padloc and t e
current
or in
speed
exceeds this limit speed.
- Contact our after-sales department to modify or remove the limit
speed programmed.
Содержание CS 30-18
