Monoprice 24179 Скачать руководство пользователя | Manualshive

Страница: 35 / 35

background image

35

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:



Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.



Consult the dealer or an experienced radio/TV technician for help.

Notice for Industry Canada

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Blackbird™ is a trademark of Monoprice Inc.
HDMI®, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC in the United States and other countries.
PlayStation® is a registered trademark of Sony Computer Entertainment Inc. PS4™ is a
trademark of the same company.

«
...
33
34
35

Содержание 24179




































Отзывы:

Нет отзывов

Похожие инструкции для 24179

Бренд: N-Tron Страницы: 18

Бренд: D-Box Страницы: 27

Бренд: FANATEC Страницы: 40

Бренд: H3C Страницы: 13

Бренд: H3C Страницы: 207

Бренд: H3C Страницы: 62

Бренд: 3Com Страницы: 12

S7906E - Switch

Бренд: 3Com Страницы: 8

TRIPP LITE Series

Бренд: Eaton Страницы: 8

Бренд: NETGEAR Страницы: 36

Бренд: Manhattan Страницы: 2

LambdaUnite MSS

Бренд: Lucent Technologies Страницы: 388

Бренд: WoMaster Страницы: 2

Raritan Dominion LX II

Бренд: LEGRAND Страницы: 7

Бренд: Grozone Control Страницы: 20

Draco tera compact 480 Series

Бренд: Ihse Страницы: 244

Бренд: Gembird Страницы: 2

AMX ENOVA DVX-3250HD-SP

Бренд: Harman Страницы: 119

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды