background image

Mode Lighting Ltd. The Maltings, 63 High Street, Ware, Hertfordshire, SG12 9AD. United Kingdom.

Tel: +44 (0) 1920 462121 

|

 Fax: +44 (0) 1920 466881 

|

 Email: [email protected] 

|

 www.modelighting.com

SceneStyLED from Mode is the stylish way to control your lighting. Self-con-
tained, they connect to your existing wiring without fuss and can control 
up to four independent circuits of lighting depending on the unit selected. 
SceneStyle can quickly and easily be programmed by the user to store any 
combination of four moods or “scenes”, as well as on and off.

By selecting the different scenes, areas of your home can have completely 
different lighting atmospheres to suit your use of the space. So you can 
turn your living room into a home cinema, the day room into a quiet snug 
and the conservatory into a dining room, all at the touch of a button. You 
can also select “full on” for cleaning or manually increase or decrease the 
brightness of an individual scene or circuit.
Each scene can be any combination of the lighting circuits at any brightness 
level from a soft glow to a bright illumination. Even the time taken to “fade” 
between each different mood is programmable.

For example, in a kitchen-diner, you may install a SceneStyle4 controlling 
low voltage recessed down-lights in the ceiling, mains voltage wall lights, 
low voltage task lights under the wall cabinets and a pendant light over the 
dining table. By simply pressing a button, you can choose to alter the light-
ing levels to suit “food preparation”, a “family meal”, a “romantic dinner” 
or a “vibrant” party mode.

www.modelighting.com

DS540 V1.0

Содержание SceneStyLED4

































Отзывы: