Mode Lighting SceneStyLED4 Скачать руководство пользователя | Manualshive

Страница: 11 / 32

background image

Configuration Menus

10

UNDERSTANDING THE CONFIGURATION MENU

The configuration menus can be used to configure advanced features of SceneStyle. To return
to the main screen at any point, press the bottom right button repeatedly until the main
screen appears. For experienced users, a complete diagram of the configuration menus is
provided at the back of the manual.

Entering The Configuration Menus

To enter the main config menu, hold the bottom two buttons for one second until they are lit
red. Release the bottom two buttons and then press buttons two and one alternately in the
pattern 2, 1, 2, 1 to enter the menu.

MAIN CONFIGURATION MENU

The main config menu can be used to perform a factory restore and to access the three
further configuration menus.

Factory Restore

Factory restore resets every scene, colour and setting to the factory defaults. To perform a factory
reset, hold the factory restore button for five seconds. The button can be released once all buttons
start flashing yellow. Once complete, SceneStyle will automatically return to the main screen.

«
...
9
10
11
12
13
...
»

Содержание SceneStyLED4

































Отзывы:

Нет отзывов

Похожие инструкции для SceneStyLED4

Бренд: NCR Страницы: 6

Бренд: Garmin Страницы: 12

Бренд: IBM Страницы: 12

Бренд: K&K Страницы: 10

Бренд: Aaeon Страницы: 76

Бренд: H3C Страницы: 5

Бренд: H3C Страницы: 27

Бренд: H3C Страницы: 4

Бренд: H3C Страницы: 54

Бренд: H3C Страницы: 10

Бренд: H3C Страницы: 10

Бренд: Lamtec Страницы: 22

xPico 200 Series

Бренд: Lantronix Страницы: 7

Бренд: Lantronix Страницы: 3

Бренд: Lantronix Страницы: 15

Бренд: Nacon Страницы: 24

Бренд: NAD Страницы: 4

Бренд: NAD Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды