Mode Lighting SceneStyLED4 Скачать руководство пользователя | Manualshive

Страница: 14 / 32

background image

Circuit Configuration Menu

13

Minimum Brightness

With compatible light fittings, it may be possible to reduce the minimum circuit brightness,
although incompatible fittings may begin to flicker at lower light levels. To reduce this
brightness, first briefly press the minimum brightness button which will lead to a second
menu being displayed. The minimum light level can then be adjusted using the raise and
lower buttons.

Toggle Level

Toggle level can only be adjusted if SceneStyle is configured to toggle to a defined light level.
To configure SceneStyle to toggle to a defined light level, see Entering the configuration
menus

(p.10)

, followed by the Operation configuration menu

(p.11)

.

Toggle level is the light level to which circuits will be set if SceneStyle has been configured to
toggle to a defined light level. To adjust toggle level, first briefly press the toggle level button,
which will lead to a second menu being displayed. The toggle level can then be adjusted by
using the raise and lower buttons.

Switched

A circuit which is set to switched cannot be dimmed to different light levels and will therefore
operate as if controlled by a normal on/off switch. To change a circuit between being dim-
mable and switched, briefly press the switched button. When lit green, the circuit is switched
and cannot be dimmed.

«
...
12
13
14
15
16
...
»

Содержание SceneStyLED4

































Отзывы:

Нет отзывов

Похожие инструкции для SceneStyLED4

Бренд: ABB Страницы: 30

Бренд: ABB Страницы: 15

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 44

Бренд: Wavelink Страницы: 69

VLT AutomationDrive FC 302

Бренд: Danfoss Страницы: 128

VLT DriveMotor FCP 106

Бренд: Danfoss Страницы: 4

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 8

Бренд: Gascat Страницы: 32

Бренд: Rachio Страницы: 2

Бренд: Paradox Страницы: 32

Бренд: Parker Страницы: 4

Wireless Blade FX Controller for Wii

Бренд: Datel Страницы: 2

COMBIVERT F4-S/1.2

Бренд: KEB Страницы: 96

Smart 4 Universal

Бренд: Classic Страницы: 12

Бренд: Pilz Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды