Mizuho MOT-VS700 Series Скачать руководство пользователя страница 75

Страница: 75 / 83

Troubleshootin

Message

Possible cause and measures

25. Tilt Sensor

The sensor for Trendelenburg and lateral tilt has any abnormality.
Request repairs from your distributor or Mizuho.

27. Back Potentiometer

The sensor for the back plate has any abnormality. Request repairs
from your distributor or Mizuho.

28. Slide Potentiometer

The sensor for sliding has any abnormality. Request repairs from your
distributor or Mizuho.

29. Leg(R) Potentiometer

The sensor for the right leg plate has any abnormality. Request
repairs from your distributor or Mizuho.

30. Leg(L) Potentiometer

The sensor for the left leg plate has any abnormality. Request repairs
from your distributor or Mizuho.

31. Hand Control Connection

The control unit isn't connected.

33. Memory Function

Because the sensor function has any abnormality, the memory
function cannot be used.

36. Offset Load

The operating table is at risk of tipping over.

37. Offset Load(Danger)

38. Loadcell Disconnection

The tipping over detection program has any abnormality. Request
repairs from your distributor or Mizuho.

39. Loadcell Output Abnormal

The tipping over detection program has any abnormality. Request
repairs from your distributor or Mizuho.

43. Table Section Collision

The slide cylinder is about to contact with the operating table.

46. Battery communication error

The battery is out of communication. Request repairs from your
distributor or Mizuho.

47. Infrared remote mode

operation prohibition

In the reverse mode, the infrared mode is disabled.

48. Battery high temperature

warning

Stop the operation immediately and request repairs from your
distributor or Mizuho.

49. "FLEX" operation prohibition

are disabled.

Error/warning for the display monitor

Monitor

Measures

Panel Err.

The operating table cannot communicate with the touch panel. Request repairs from
your distributor or Mizuho.

Содержание MOT-VS700 Series




















































































Результаты поиска

Содержание MOT-VS700 Series

Отзывы:

Похожие инструкции для MOT-VS700 Series

Бренды по названию

Популярные бренды

Mizuho MOT-VS700 Series, Руководство оператора

Результаты поиска

Содержание MOT-VS700 Series

Отзывы:

Похожие инструкции для MOT-VS700 Series

Бренды по названию

Популярные бренды