Mizuho MOT-VS700 Series Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 83

background image

51

4

Operatio

n

Deactivating the reverse mode

1.

Select

and select the reverse mode (Reverse

Orientation).

2.

Press

.

The reverse mode is deactivated.

CAUTION

The reverse mode deactivate the following
functions.

Flexing

Beach chair

In addition, the reverse mode cannot be used
under the conditions below.

When using the Double Leg Section
The page shown above does not appear.

When operating with the touch panel
Only the normal operation is available.
When operating with the foot switch
Only the normal operation is available.
Operation via wireless infra-red communication
The wireless infra-red operation is disabled in
the reverse mode.

NOTE

The reverse mode is kept
even after the power is turned
off. Deactivate the reverse

mode, if unnecessary.

When operating with the memory
The page shown above does not appear.

The reverse mode deactivates

when using the Double Leg

section.

NOTE

Operating with the reverse

mode restricts the range of

movement below.

・

Trendelenburg

head down:30°

head up :40°

・

Back plate bending

Up :25°

down:90°

・

Leg plate bending

Up :90°

down:40°

・

Slide

To head:415mm

To leg :250mm

Other operations activate the

same as normal mode.

«
...
53
54
55
56
57
...
»

Содержание MOT-VS700 Series




















































































Отзывы:

Нет отзывов

Похожие инструкции для MOT-VS700 Series

Бренд: Tanco Страницы: 72

Бренд: HABYS Страницы: 16

Бренд: Acterna Страницы: 72

Бренд: Taylor Made Страницы: 2

Бренд: York Fitness Страницы: 18

Бренд: Safco Страницы: 2

Бренд: Omni Страницы: 193

Бренд: Datavideo Страницы: 50

Бренд: Waterous Страницы: 90

Бренд: Campbell Страницы: 14

Бренд: Modulate Страницы: 2

Бренд: E-Z DRILL Страницы: 12

Бренд: e-survey Страницы: 54

Бренд: E-Pill Страницы: 8

XL-7 Command Station

Бренд: E-Mu Страницы: 22

AURO SPOT CLAS100

Бренд: Cameo Страницы: 60

Бренд: Sweet Sound Electronics Страницы: 6

Бренд: Neilsen Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды