Mizuho MOT-VS700 Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 83

background image

28

4

Operatio

n

<Important> Using the control unit with other
operating table (MOT-VS700)

When using the current control unit with other MOT-VS700, be sure to
cancel the Bluetooth information (paring) by following the procedure below.

1.

Turn "BT" to "ON" and tap "CLEAR", then wait for 12
seconds.

The address turns to "0".

If using the control unit with other MOT-VS700 without cancelling of the
Bluetooth information, the following restrictions will happen in operation.

Using under connection by wire

No restriction occurs in the wired connection.
However, if you once used by wire, the control unit cannot be connected
again with the original MOT-VS700 via Bluetooth and following warning
screen opens.

Bluetooth

connection

is forcibly

canceled.

Warning screen of the control unit

Using under connection via Bluetooth

When you connect with other MOT-VS700 via Bluetooth, be sure to

The operating table to be connected via Bluetooth is recognized.
However, the control unit may connect with the original MOT-VS700, if it is
nearby, due to nature of Bluetooth.
Be sure to follow the procedure described above to cancel the original
paring information and then try the connection.

«
...
30
31
32
33
34
...
»

Содержание MOT-VS700 Series




















































































Отзывы:

Нет отзывов

Похожие инструкции для MOT-VS700 Series

DVCPRO P2 Series

Бренд: Panasonic Страницы: 32

Бренд: ZIGBEE Страницы: 6

Бренд: Daisy Страницы: 2

Below Ground Pool Cover Box

Бренд: Daisy Страницы: 3

Бренд: Danelec Страницы: 67

Бренд: Datalogic Страницы: 20

Бренд: Datalogic Страницы: 188

BOMAG BW 100 ADM-5

Бренд: Fayat Страницы: 216

Бренд: B medical systems Страницы: 28

Бренд: Ransomes Страницы: 282

Ransomes HR 6010

Бренд: Jacobsen Страницы: 10

Бренд: QRS Страницы: 16

Бренд: QMAXZ Lighting Страницы: 36

Бренд: Labnet Страницы: 12

Бренд: Waterpik Страницы: 2

AirForm Night Splint

Бренд: Össur Страницы: 16

Бренд: Össur Страницы: 17

Бренд: Tieline Страницы: 359

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды