Mitutoyo ST36 Скачать руководство пользователя страница 3

Страница: 3 / 66

No. 99MBE048B

CONVENTIONS USED IN MANUALS

Conventions used in Mitutoyo’s User’s Manual are roughly divided into three types (safety reminders,

prohibited and mandatory actions, and referential information and locations). Moreover, these conven-

tions include general warnings and specific warnings. Specific warning symbols are provided with con

crete pictograms inside of them.

Safety reminder conventions and wording warning against potential haz-

ards

DANGER

Indicates an immediately hazardous situation which, if not avoided, will result

in serious injury or death.

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result

in serious injury or death.

CAUTION

Indicates a potentially hazardous situation which, if not avoided, may result in

minor injury.

NOTICE

Indicates a potentially hazardous situation which, if not avoided, may result in

property damage.

Alerts the user to a specific hazardous situation that means "Caution, risk of

electric shock".

Conventions and wording indicating prohibited and mandatory actions

Indicates concrete information about prohibited actions.

Indicates concrete information about mandatory actions.

Indicates that grounding needs to be implemented.

Conventions and wording indicating referential information or referential

locations

Tips

Indicates referential information such as that for when the operating methods and procedures which

are printed in these sentences are to be applied to specific conditions.

Indicates referential locations if there is information that should be referred to in this document or an

extraneous User's Manual.
E.g.: For further details on xxx, refer to

"1.2 System Configuration and Name of Each Part" (page 1)

Содержание ST36



































































Результаты поиска

Содержание ST36

Отзывы:

Похожие инструкции для ST36

Бренды по названию

Популярные бренды

Mitutoyo ST36, Руководство пользователя

Результаты поиска

Содержание ST36

Отзывы:

Похожие инструкции для ST36

Бренды по названию

Популярные бренды