Mitsubishi S4Q Скачать руководство пользователя страница 30

Страница: 30 / 174

30 / 174

Service Manual Mitsubishi SQ-Series diesel engines

Version 08/2004

ENGLISH

CYLINDER HEADS AND VALVE
MECHANISM

ENGINE MAIN PARTS

2) Before inserting a new valve seat, measure

the bores in the cylinder head for the valve

seats to make sure they are correct in

dimension.

3) Chill the valve seat in liquid nitrogen (about –

170°C [–274°F]) for more than 4 minutes with

the cylinder head kept at normal temperature,

or heat the cylinder head to 80 to 100°C [176

to 212°F] with the valve seat chilled in ether or

alcohol containing dry ice.

4) Use the caulking tool to install the valve seat.

Tools needed

Refacing valve face

If the valve face is badly worn, reface it with a
valve refacer.

Figure 29

Valve seat bore dimensions

Unit: mm [in.]

Inlet valve

seat bore

Exhaust valve

seat bore

45°

8 ± 0.

.346 ± 0.

004]

±0.

.346 ± 0.

004]

8 ± 0.

1 ±

004

]

8 ± 0.

1 ±

004

]

[1.61

]

+0.02

+0.0008

[1.30

]

+0.02

+0.0008

Figure 30

Installing valve seat

Caulking tool

Part number

Caulking tool (for inlet valve
seat)

30691-02700

Caulking tool (for exhaust
valve seat)

30691-02800

Figure 31

Refacing valve face

NOTE

Set a valve refacer at an angle of 30°.

Grind the valve as little as possible. If the

margin seems to exceed the repair limit as a

result of grinding, replace the valve.

Содержание S4Q















































































































































































Результаты поиска

Содержание S4Q

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi S4Q, Руководство пользователя

Результаты поиска

Содержание S4Q

Отзывы:

Бренды по названию

Популярные бренды