Mitsubishi S4Q Скачать руководство пользователя страница 132

Страница: 132 / 174

132 / 174

Service Manual Mitsubishi SQ-Series diesel engines

Version 08/2004

ENGLISH

ALTERNATOR

ELECTRICAL SYSTEM

3) To install new brushes, press them into the

brush holders as shown in the diagram, then

solder the lead wires.

28.5 Assembly

To reassemble, follow the disassembly sequence in

reverse.

Be sure to observe the following during assembly.

28.5.1 Key points in reassembly

When press-fitting the rear bearing into the rear

bracket, heat the rear bracket to 50 to 60°C [122 to

140°F].

The brushes must be raised before the rotor is

installed to the rear bracket. To do so, put a wire

through the small hole located on the rear bracket,

then remove the wire after completing the

reassembly.

28.6 Installation

Install the fan belt on the alternator, and mount the

alternator on the engine.

Temporarily tighten all the bolts.

Insert a bar between the alternator and crankcase.

Using the bar as leverage, move the alternator and

adjust the belt tension.

While keeping the alternator at that position,

tighten the bolt that secures the alternator to the

adjusting plate.

Figure 201 Replacement of brushes

Figure 202 Reassembly of alternator

Wire

Rear bracket

Wire

Brush

Figure 203 Installation of alternator

Содержание S4Q















































































































































































Результаты поиска

Содержание S4Q

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi S4Q, Руководство пользователя

Результаты поиска

Содержание S4Q

Отзывы:

Бренды по названию

Популярные бренды