Mitsubishi S4Q Скачать руководство пользователя страница 160

Страница: 160 / 174

160 / 174

Service Manual Mitsubishi SQ-Series diesel engines

Version 08/2004

ENGLISH

MAINTENANCE STANDARDS TABLE

MAINTENANCE STANDARDS

MAINTENANCE STANDARDS

35 MAINTENANCE

STANDARDS TABLE

Unit: mm [in.]

Group

Inspection Point

Nominal

Value

Assembly

Standard

(Standard

Clearance)

Repair Limit

(Clearance)

Service

Limit

(Clearance)

Remark

Gener

Maximum speed, (no-load), rpm

Vary according to

specifications

Adjust governor setting.

Minimum speed, (no-load), rpm

Compression pressure, MPa
(kgf/cm

) [psi]

2.94 (30) [427] at 150 to 200

rpm

2.55 (26) [370]

Oil and water temp.
20 to 30°C [68 to 86°F]

Engine oil pressure, MPa (kgf/
cm

) [psi]

0.2 to 0.4 (2 to 4) [28 to 57] at

rated rpm

0.15 (1.5)

[21.3]

Oil temperature
70 to 90°C
[158 to 194°F]

0.1 (1) [14] or more at low idle

speed

0.05 (0.5) [7]

Valve timing

Inlet valves open

Inlet valves close

Exhaust valves open

Exhaust valves closed

BTDC 30°

ATDC 50°

BTDC 74°

ATDC 30°

±3° (crank angle)

Valve clearance (cold)

0.25 [0.0098]

Bolt inlet and exhaust valves.

Fuel injection timing

BTDC 20°

Standard injection timing is
indicated here. The timing for
each model of engine varies
according to its specification.
Be sure to verify the timing by
referring to the specifications
of each model.

Fan (water pump) and alternator
drive belt tension

13 [0.5], approx.

When belt is pushed inward
with 98 N (22 lbf) [10 kgf]
pressure exerted midway
between crankshaft and
alternator pulleys.

Engine Main Part

Crankcase

Flatness of
surface gasket

0.05 [0.0020] or

less

0.20

[0.0079]

Regrind if warpage is minor.

Cylinder

Inside diameter

[3.46]

[3.46

]

Increase bore to 0.25 [0.0098]
or 0.50 [0.0197] oversize and
use oversize piston.

Circularity

0.01 [0.0004] or

less

Cylindricity

0.015 [0.0006] or

less

Main bearing

Bore for main bea

rin

Inside diameter

[2.72]

[2.72

]

With main bearing cap
installed (bolts tightened).

Out-of-round

0.02 [0.0008] or

less

Concentricity

0.05 [0.0020] or

less

+0.035

+0.0014

+0.019

+0.0008

Содержание S4Q















































































































































































Результаты поиска

Содержание S4Q

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi S4Q, Руководство пользователя

Результаты поиска

Содержание S4Q

Отзывы:

Бренды по названию

Популярные бренды