manualshive.com logo in svg

Mitsubishi S4Q, Руководство пользователя

Поделиться
Скачать
Mitsubishi S4Q Скачать руководство пользователя страница 125

125 / 174

Service Manual Mitsubishi SQ-Series diesel engines
Version 08/2004

ALTERNATOR

ENGLISH

ELECTRICAL SYSTEM

28.1.2 Inspection of adjustment voltage 

(unit with integrated IC regulator)

1.

Disconnect the cable from the positive (+) terminal 

of the battery, and connect an ammeter between 

the terminal and cable.

2.

Connect a voltmeter between terminal L and 

ground.

3.

Make sure that the voltmeter indicates “0” when 

the starter switch is turned off.

Make sure that the voltmeter indicates a voltage 

level sufficiently lower than the battery voltage 

when the starter switch is turned on (without 

starting the engine).

4.

Short-circuit the terminal of the ammeter, and start 

the engine.

5.

Read the indication (adjustment voltage) on the 

voltmeter with the ammeter indicating 5 A or lower, 

the engine operating at 1800 to 2500 rpm, and the 

lamp switches turned off.

Unit: V

28.1.3 Inspection of output (unit with 

integrated IC regulator)

1.

Disconnect the grounding cable from the battery.

2.

Disconnect the wire from terminal B of the 

alternator, and connect an ammeter. Connect a 

voltmeter between terminal B and ground.

3.

Connect the grounding cable to the battery.

4.

Start the engine.

5.

Immediately after the engine starts, turn on all load 

devices such as lamps.

6.

Increase the engine speed. When the voltmeter 

indicates 27.0 V, read the maximum current at the 

specified alternator rotation speed.

If the measured value conforms to the standard 

value, the alternator is normal.

Figure 187 Inspection of adjustment voltage

12V

+

-

+

-

A

V

+

L

R

Switch

Voltmeter

24V (option)

Ammeter

Battery

Item

Standard 

Value

V-kW

Adjustment 
voltage at 20°C

14.7 ± 0.5

12-50

Option

28.5 ± 0.5

Option

24-25
24.35

Figure 188 Wiring diagram for output test (unit with 

integrated IC regulator)

L

R

B

+

V

A

Switch

Voltmeter

Ammeter

Charge 

lamp

Содержание S4Q















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды