Mitsubishi S4Q Скачать руководство пользователя страница 102

Страница: 102 / 174

102 / 174

Service Manual Mitsubishi SQ-Series diesel engines

Version 08/2004

ENGLISH

FUEL INJECTION NOZZLES

FUEL SYSTEM

21.2 Testing

Injection pressure (valve opening pressure)

1) Install the injection nozzle on the tester. Slowly

operate the tester handle full strokes to bleed

(remove) air from the pipe and nozzle.

2) Make a slow increase in pressure by

operating the tester handle at a speed of more

than one stroke per second while observing

the pressure gage.

3) The pressure gage reading will slowly

increase and, when the nozzle starts

discharging fuel, it will go down fast. Take the

gage reading right then as the injection

pressure.

Unit: MPa (kgf/cm

) [psi]

4) If the injection pressure is not correct, make

an adjustment of the nozzle by adding or

removing the shims inside the nozzle holder.

Figure 170 Testing fuel injection nozzle

Item

Assembly Standard

Injection pressure

14.22

(145 )

[2063

]

CAUTION

When testing the injection nozzle, keep its tip pointed

away from the operator. Fuel from the orifices in the

tip of the nozzle is under high pressure and can

cause injury to the operator.

+0.78

+113

Figure 171 Removing nozzle tip

Содержание S4Q















































































































































































Результаты поиска

Содержание S4Q

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi S4Q, Руководство пользователя

Результаты поиска

Содержание S4Q

Отзывы:

Бренды по названию

Популярные бренды