Mitsubishi S4Q Скачать руководство пользователя страница 29

Страница: 29 / 174

29 / 174

Service Manual Mitsubishi SQ-Series diesel engines
Version 08/2004

CYLINDER HEADS AND VALVE

MECHANISM

ENGLISH

ENGINE MAIN PARTS

Unit: mm [in.]

Replacing valve seat

1) Weld a stud to the valve seat. Insert a shaft

through the valve guide from the upper side of

the cylinder head to put its end on the stud, as

shown in the illustration. Then, drive the seat

off from the cylinder head.

Figure 26

Valve contact pattern

Good

Bad

NOTE

Check the valve contact after checking or

replacing the valve guides.

Do not rotate the valve when holding it

against the seat for checking the contact.

After refacing or replacing the valve or valve

seat, lap the valve in the seat. (See (8)

Lapping valves.)

Figure 27

Valve contact with valve seat

Valve seat angle

Valve

sinkage

Valve seat width

Valve

margin

Item

Nominal

Value

Assembly

Standard

Repair

Limit

ve se

Angle

30°

Width

1.18

[0.05]

1.04 to 1.32

[0.0409 to 0.0520]

1.6

[0.0630]

Valve
sinkage

0.8

[0.03]

0.7 to 0.9

[0.0276 to 0.0354]

1.3

[0.0512]

Valve margin

1.70

[0.07]

1.20

[0.0472]

Figure 28

Replacing valve seat

Weld

Bar

Valve seat

Stud

Valve seat

NOTE

When welding the stud to the valve seat, avoid

contact of any spatter with the machined surface of

the cylinder head.

Содержание S4Q















































































































































































Результаты поиска

Содержание S4Q

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi S4Q, Руководство пользователя

Результаты поиска

Содержание S4Q

Отзывы:

Бренды по названию

Популярные бренды