Mitsubishi MELSEC-A AJ65VBTCU-68DAVN Скачать руководство пользователя | Manualshive

Страница: 58 / 104

background image

4 - 19 4 - 19

MELSEC-A

4 SETUP AND PREPARATION BEFORE OPERATION

4.10.2 Wiring procedures for the one-touch connector for communication

This section provides the wiring procedures of the one-touch connector for
communication.

Plug body

Plug cover

Metal contact

1) Check the connector.

Check that the plug cover is attached to the plug body.

Note: Do not push the plug cover into the plug body.

Once pressed, the plug cannot be used any more.

Cut the shield wire, aluminum tape and braid.

DA (Blue)
DB (White)
DG (Yellow)
Drain wire (AWG20)

Stretch the drain wire and twist it from the base.

(3cm in length, 7 times or more)

2) Processing for communication cable

Strip the cable 3cm or more and perform the processing
indicated at left.
If the electric wire lengths are not even, trim their ends with a
nipper to the same length so as to insert them neatly into a
connector.

5 4 3 2 1

Signal name

DA (Blue)
DB (White)
DG (Yellow)

NC

SLD

1m

m o

r le

ss

Metal contacts

3) Insert the cable.

Lift the end of the plug cover and insert the cable until it almost
reaches the plug body (within 1mm from the other end of the
plug cover).
Insufficient cable insertion may cause improper press fitting.

Note: When inserting the cable, prevent the cable from sticking

out from the plug cover end.

Metal contacts

4) Set the plug cover.

After inserting the cable, put down the plug cover so that its
face is horizontal to the plug surface, allowing the metal
contacts to be fitted into the plug cover.

Pliers

5) Press the center part of the plug cover.

Using pliers, press the center part of the plug cover vertically
and strongly.

For the one-touch connectors, use adjustable pliers so that their
jaws can be widely opened.

(To the next page)

«
...
56
57
58
59
60
...
»

Содержание MELSEC-A AJ65VBTCU-68DAVN









































































































Отзывы:

Нет отзывов

Похожие инструкции для MELSEC-A AJ65VBTCU-68DAVN

Бренд: MADRIX Страницы: 36

Бренд: lasmex Страницы: 10

OmniConverter GPoE+/S

Бренд: OST Страницы: 10

AVerCaster HD Duet

Бренд: Avermedia Страницы: 4

Бренд: B&K Страницы: 2

Бренд: Hamron Страницы: 28

Pro Enigma MI-X450

Бренд: Aiwa Страницы: 13

Бренд: Lechpol Страницы: 2

Бренд: Thor Broadcast Страницы: 9

Бренд: Meicheng Страницы: 6

Бренд: StarTech.com Страницы: 12

Бренд: Datavideo Страницы: 52

Бренд: Wagan Страницы: 11

OPS500-501 Series

Бренд: AXIOMTEK Страницы: 54

DA1-34072FB-B20C

Бренд: Eaton Страницы: 16

SA-1000K Series

Бренд: Samlexpower Страницы: 23

Бренд: CEL-MAR Страницы: 16

Бренд: Duracell Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды