Mitsubishi M80 series, Руководство по подключению и настройке

Страница: 396 / 542

M800S/M80 Series Connection and Setup Manual
19 Setting the Parameters and Date/Time
359 IB-1501269-F
Configuration example for seven part systems (Number of axes per part system: 8, 1, 1, 1, 1, 1, 3)
(Assumed to use the device of each part system in the ladder as follows:)
$1 Axis 1 [Axis 1]
→
(1), $1 Axis 2 [Axis 2]
→
(2),
$1 Axis 3 [Axis 3]
→
(3), $1 Axis 4 [Axis 4]
→
(4),
$1 Axis 5 [Axis 5]
→
(5), $1 Axis 6 [Axis 6]
→
(6),
$1 Axis 7 [Axis 7] → (7), $1 Axis 8 [Axis 8] → (8),
$2 Axis 1 [Axis 9]
→
(9), $3 Axis 1 [Axis 10]
→
(10),
$4 Axis 1 [Axis 11]
→
(11), $5 Axis 2 [Axis 12]
→
(12),
$6 Axis 1 [Axis 13] → (13), $7 Axis 1 [Axis 14] → (14),
$7 Axis 2 [Axis 15]
→
(15), $7 Axis 3 [Axis 16]
→
(16)
(Note) (17) to (32) are unused areas.
Parameter setting value (For the above configuration example):
Base common parameters
"#1041 I_inch (Initial state (inch))"
"#1042 pcinch (PLC axis command (inch))"
"#1239 set11/bit1 (Handle I/F selection)"
"#1240 set12/bit0 (Handle input pulse)"
Axis specification parameter
"#2001 rapid (Rapid traverse rate)"
"#2002 clamp (Cutting feedrate for clamp function)"
"#2003 smgst (Acceleration and deceleration modes)"
"#2004 G0tL (G0 time constant)"
”#2005 G0t1(G0 time constant(primary delay)"
"#2007 G0tL (G1 time constant)"
"#2008 G1t1(G1 time constant (primary delay))"
Spindle specification parameter
"#3001 slimt1 (Limit rotation speed (Gear: 00))"
"#3002 slimt2 (Limit rotation speed (Gear: 01))"
"#3003 slimt3 (Limit rotation speed (Gear: 10))"
"#3004 slimt4 (Limit rotation speed (Gear: 11))"
"#3005 smax1 (Maximum rotation speed (Gear: 00))"
"#3006 smax2 (Maximum rotation speed (Gear: 01))"
"#3007 smax3 (Maximum rotation speed (Gear: 10))"
"#3008 smax4 (Maximum rotation speed (Gear: 11))"
"#3023 smini (Minimum rotation speed)"
"#3024 sout (Spindle connection)"
"#3031 smcp_no (Drive unit I/F channel No.(spindle))"
"#3109 zdetspd (Z phase detection speed)"
Set the servo parameters according to the instruction manual for your drive. Set the spindle parameters according
to "Parameter setting list".
(3) Turn the power OFF and ON.
Axis 1 Axis 2 Axis 3 Axis 4 Axis 5 Axis 6 Axis 7 Axis 8
#1603 1 2 3 4 5 6 7 8
Axis 9 Axis 10 Axis 11 Axis 12 Axis 13 Axis 14 Axis 15 Axis 16
#1603 9 10 11 12 13 14 15 16