Mitsubishi LGH-100RX5-E, Руководство пользователя

Страница: 20 / 123

—20—
BLACK
BLACK
LS
LS
BLACK
BLACK
RED
WHITE
TR2
x201
x202
x203
x101
x102
x103
M
M
M
1
2
1
M
2
EXHAUST
SUPPLY
EXHAUST
FAN MOTOR
FAN MOTOR
FAN MOTOR
SUPPLY
FAN MOTOR
C
C
C
C
cable
transmission
M-NET
MELANS
(non-polar)
Mr.Slim
output 7 , 8
Malfunction monitor
monitor output 6 , 7
By-pass or Delay2
Shield Wire
12V or 24V DC
BROWN
RED
TM4
CN16
10
8 7 6 1 2 3
CN5
1
2
9
A B S
X10
CN32
X11 X12
Isolator
TAB2
TAB1
CN9
CN10
TAB5 TAB3
TM3 TB5
Transmission
cable
60DR-E
PZ-
BROWN
TM2
ORANGE
ORANGE
ORANGE
ORANGE
TH2 (RA)
TH1 (OA)
SW1
SW5
SW2
SA1 SA2
BLACK
GREY
YELLOW
ORANGE
WHITE
BLUE
BLUE
RED
BROWN
BROWN
BLUE
CN7
CN2
CN1
TM1
monitor output
Operation or Delay1
PE
N
N
L L
24VDC 2A 5VDC 100mA
MAX 240VAC 2A MIN 220VAC 100mA
(non-polar)
TR1
BROWN
BLACK
GREY
YELLOW
YELLOW
GREY
BLACK
BROWN
WHITE
BLUE
ORANGE
RED
RED
ORANGE
BLUE
WHITE
3 1
Unchanged a-contact
External control input
A
2nd or later main units
cable
transmission
M-NET
S B
TB5 (M-NET)
Shield Wire
TM4
(PZ-60DR-E)
2nd remote controller
installable)
(*1)
Optional Remote controller
(Max. two remote controllers
PZ-41SLB-E and PZ-52SF-E cannot
be used when using PZ-60DR-E.
(*1)
5VDC 100mA
MIN 220VAC 100mA
24VDC 1A
MAX 240VAC 1A
transmission wire to , on TB5 terminal B A
2
1
of TM4 terminal block, and connect M-NET
is used as the M-NET System, connect it to
block.
*When the optional Remote Controller PZ-60DR-E
GM MG
GM MG
x103
x102
x101
x203
x202
x201
2
1
POWER SUPPLY
220-240V 50Hz
CN16
(Unchanged a-contact)
RED
BROWN
YELLOW
ORANGE
GREEN
HI
LO
BY-PASS
With this product, the wiring installation method will
vary according to the design of the system.
Perform electrical installation to meet local electrical regulations.
.Always use double insulated PVC cable for the transmission cables.
.Wiring work must be performed by qualified professionals.
.All supply circuits must be disconnected before obtaining access to the terminal devices.
NOTE 1.TM1, TM2, TM3, TM4, TB5 shown
in dotted lines are field work.
2.Isolator should be provided by the customer.
3.Be sure to connect the grounding wire.
*Attention
2nd remote controller (Max. two remote controllers installable)
2nd LOSSNAY unit (Up to max 15 units)
(*1)
LGH-150RX
5
-E, LGH-200RX
5
-E
Definition of Symbols
M1: Motor for exhaust fan X10,X11,X12: Relay contact
M2: Motor for supply fan X101,X102,X103: Relay Supply fan speed control
C: Capacitor X201,X202,X203: Relay Exhaust fan speed control
GM: Motor for By-pass operation CN1: Connector (Transformer primary)
LS: Microswitch CN2: Connector (Transformer secondary)
TH1: Thermistor for outside air CN5: Connector (Thermistor)
TH2: Thermistor for return air CN6: Connector(Microswitch)
SW1: Switch (Main/Sub change) CN7: Connector (Motor for By-pass operation)
SW2, 5: Switch (Function selection) CN9: Connector (Fan motor)
TM1: Terminal block (Power supply) TAB3: Tab connector (Fan motor)
TM2: Terminal block(External control input) TAB5: Tab connector (Fan motor)
TM3: Terminal block (Monitor output) CN9: Connector (Fan motor)
TM4: Terminal block CN10: Connector (Fan motor)
(Transmission cable and monitor output) CN16: Connector(High/Low/By-pass switch)
TB5: Terminal block (M-NET Transmission cable) CN32: Connector (Remote control selection)
TAB1,TAB2: Connector (Power supply) SA1: Address setting rotary switch (10 digit)
TR1: Control circuit transformer SA2: Address setting rotary switch (1 digit)
TR2,TR3: By-pass operation transformer SYMBOL : Indicates terminal block.
Board insertion connector or fastening
connector of control board.
*Specifications may be subject to change without notice.