Mitsubishi LE-40MTB-E, Инструкция по эксплуатации

Страница: 14 / 80

10
4.3 Adjustment of zero and span for tension detector
F L L S C A L E S E T T E N S I O N F U L L S C A L E
„ S E T
→
# # # # N : × 1 0 : „ × 1 : × 0 . 1
U
Z R O T U N E E X E C U T E T E N S I O N Z E R O T U N I N G
P U S H < E N T E R > O R < C A N C E L >
E
S A N T U N E P S E T N U M B E R O F T N S N . D E T E C T O R
T N S N . D T :
„
T O W : O N L Y O N E
S A N T U N E E X E C U T E T E N S I O N S P A N T U N I N G
P U S H < E N T E R > O R < C A N C E L >
P
S A N T U N E S U S P E N D T E S T W E I G H T
W E I G H T
→
# # # # N S E T W E I G H T
P
S A N T U N E C O N T . T E N S I O N S P A N T U N I N G ?
P U S H < E N T E R > O R < C A N C E L >
P
S T T H E D R I V I N G P A R A M E T E R S E
P S S W O R D
„ „ „ „ „ „ „ „ „ „ „ „ „ „ „ „
S E T
→
# # # # # S E T N U M B E R
A
T
T
S
• This is to set the full-scale
tension (maximum
mechanical tension) and the
number of display digits.
For example, if desired to
have "50.0N" displayed,
select " 500 " and " × 0.1 ".
• Zero adjustment should be
made with the tare weight of
the detection reel and
without material.
• If unable to make zero
adjustment, check the
system referring to pages 75
and 77.
• If the tension full scale is
changed, carry out the
zero/span adjustment again.
• Install the tension detectors
on both ends of the
detection reel as shown in
the left figure. For a short
detection reel, only one
tension detector may be
used. Use the following
screen to select one or two
tension detectors.
ENTER CANCEL
Stand- by(for approximately 10sec)
S
T
E R O T U Z Z R O T U N E E - - - N I N G E R R O R
T H E D E T E C T I O N R O L L E R I S T O O H
Z R O T U N E
C M P L E T E O
E
!
Finished
Error
ENTER CANCEL
• Suspend weight W (N).
The weight should be a
static load as close to the
full-scale tension value as
possible
(Should be between 1 to 1/3
of the full scale).
Stretch a string in
the center of the
roller.
ENTER
W X T
NUMERIC
T
ENTER CANCEL
T
S A N T U N E C O M P L E T E !
L E F T
→
# # # # N :
P
P A N T U S S A N T U N P E - - - N I N G E R R O R
S P A N T U N I N G T A R G E T W E I G H T I S
Error
Finished
S
T
C E C K C H E C K T H E P A R A M E T E R S
P U S H < E N T E R >
H
ENTER
Error Message
• When, for example, a mass
of 10 kg is suspended,
multiply it by the
gravitational acceleration
(9.8) to make it 98N.
• Do not alter the load during
the adjustment. Otherwise,
the system may not be able
to adjust or may generate
an error.
• By the display unit setting,
the system shows the value
in the magnitude of "N" or
"×10N". When one tension
detector is used, the left
display shows zero. When
two detectors are used, the
left and right readings are
balanced.
• When unable to adjust the
span, check the system
referring to pages 75 and
77.
• If an error message
appears, the system can
not complete the
adjustment. Set the
system again.
• Initial setting completed.
The system setting screen
appears hereafter. Set the
parameters as necessary.
T
T
T