Mitsubishi LE-40MTB-E, Инструкция по эксплуатации

Страница: 13 / 80

9
C T L . P A R T S E L E C T O R E E L R R O L L
„
U N W I N D : W I N D : F E E D
N
R E L N U M . S E L E C T R E E L N U M B E R
„ 1 R E E L : R E E L S
E
T P E R S E L E C T T A P E R T E N T R N S I O N C O O L
„
O F F : O N
A
D A . S E T S E T D I A M E T E R
„
M I N . D I A
→
# # # # m m
φ
: M A X . D I A
→
# # # # m m
φ
I
A T U A T O R S E L E C T A C T U A T O R
„ P O W D E R : A C S E R V O M O T O R
C
S A L L M D . S E L E C T S T A L L S E T T N G M O D E
K E Y S E T : „ M A N . V O L .
T
S A L L R S T S E L E C T S T A L L M E M O R Y R E S E T M O D E
M C 4 o n l y : „ M C 4 + O U T S W .
T
A 2 S E L E C T A I 2 A N A L O G I N P U T
D I A . : S T A L L : N E W R . : T A P E R : T N S N .
I
M 5 S E L E C T M C 5 I N P U T
G A I N 2 : I N C H N G : O U T R M T . : C U T T R Q .
C
A 3 S E L E C T A I 3 A N A L O G I N P U T
D I A . : S T A L L : N E W R . : T A P E R : T N S N .
I
M 6 S E L E C T M C 6 I N P U T
G A I N 2 : I N C H N G : O U T R M T . : C U T T R Q .
C
T
T
T
T
T
T
• When using the NRO
(new reel output), select
"Multi-reel" mode.
( See page 24 and after )
• Normally, the taper control is
not used for unwinding
control.
• This is to select whether to use the internal
signals of the tension controller or to
receive the external reel data to calculate
the reel diameter for the taper control.
Receiving the external reel diameter results
in better taper control accuracy.See page
28 for details.
Select
“ EXT ” when using the LE-40MD
diameter calculation unit.
T R . D I A . S E L E C T T A P E R S I G N A L
„
I N T . : E X T . : L I N K
P
T P E R M D . S E L E C T T A P E R M O D E
„
L I N E A R : N O N - L I N E A R
A
• Select "POWDER" when using
hysteresis or air clutch/brake.
• When using an AC servo, if it is
not desired to reverse the
direction of torque control
between resurrection and power
run, select "POWDER".
• This is to select the input
method of the stall settings.
See page 13 for the details
related to stall.
• This is to select the input
method for resetting the stall
memory. The output on/off
switch can also control stall
memory reset.
• This is to select AI (analog)
input and MC (contact) input.
See page 26 and after for the
use of these functions.
These settings can be made on
screens other than the initial
setting.
It is all right if these settings are
made later on.
T
T
T
T
T
T
Good to " MAN.VOL "
Good to " MC4+OUTSW "
T
FE
E
D
OF
F
IN
T