Mitsubishi Electric RH-12FH Series Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 146

background image

2-11

Installation

2Unpacking to Installation

2.2.3 Installation procedures

The installation procedure of the robot arm is shown below.

Fig.2-4 ： Installation dimensions

1) The robot installation surface has been machine finished. Use the installation holes (RH-3FH/6FH: 4-φ9

holes, RH-12FH/20FH: 4-φ16 holes) opened at the four corners of the base, and securely fix the robot
with the enclosed installation bolts (hexagon socket bolts).

2) Install the robot on a level surface.
3) It is recommended that the surface roughness of the table onto which the robot is to be installed by Rz25 or

more. If the installation surface is rough, the contact with the table will be poor, and positional deviation
could occur when the robot moves.

4) When installing, use a common table to prevent the position of the devices and jigs subject to robot work

from deviating.

5) The installation surface must have sufficient strength to withstand the arm reaction during operation, and

resistance against deformation and vibration caused by the static (dynamic) load of the robot arm and
peripheral devices, etc.

6) After installing the robot, remove the self-supporting plate, hanging jig, and fixing plate.
7) If you operate the robot at a high speed, reaction forces are applied to the installation stand by the robot's

operation. Make sure that the installation stand on which the robot is placed has sufficient strength and

㻝㻡㻜

㻢㻜

㻝㻞㻜

㻥㻜

㻥㻞

㻥㻞

㻝㻤㻜

㻝㻡㻜

㻝㻣㻠

㻝㻢㻜

㻝㻤㻞

㻞㻝㻞

㻠㻙䃥㻥㻌㼕㼚㼟㼠㼍㼘㼘㼍㼠㼕㼛㼚㻌㼔㼛㼘㼑㼟

㻞㻙䃥㻢㻌㼔㼛㼘㼑㼟

㻔㼒㼛㼞㻌䃥㻤㻌㼜㼛㼟㼕㼠㼕㼛㼚㼕㼚㼓㻌㼜㼕㼚㼟㻕

㻔㻵㼚㼟㼠㼍㼘㼘㼍㼠㼕㼛㼚㻌㼞㼑㼒㼑㼞㼑㼚㼏㼑㻌㼟㼡㼞㼒㼍㼏㼑㻕

㻾㼦㻞㻡

㻾㼦㻞㻡

㻔㻵㼚㼟㼠㼍㼘㼘㼍㼠㼕㼛㼚㻌

㼞㼑㼒㼑㼞㼑㼚㼏㼑㻌㼟㼡㼞㼒㼍㼏㼑㻕

㻠㻙䃥㻝㻢㻌㼕㼚㼟㼠㼍㼘㼘㼍㼠㼕㼛㼚㻌㼔㼛㼘㼑㼟

㻝㻤㻜

㻝㻞㻜

㻝㻞㻞

㻞㻠㻜

㻝㻞㻞

㻞㻜㻜

㻞㻜㻜

㻔㻵㼚㼟㼠㼍㼘㼘㼍㼠㼕㼛㼚㻌

㼞㼑㼒㼑㼞㼑㼚㼏㼑㻌㼟㼡㼞㼒㼍㼏㼑㻕

㻔㻵㼚㼟㼠㼍㼘㼘㼍㼠㼕㼛㼚㻌㼞㼑㼒㼑㼞㼑㼚㼏㼑㻌㼟㼡㼞㼒㼍㼏㼑㻕

㻞㻠㻞

㻞㻤㻜

㻔㻝㻡㻤㻕

㻞㻞㻜

㻤㻜

㻾㼦㻞㻡

㻾㼦㻞㻡

㻞㻙䃥㻢㻌㼔㼛㼘㼑㼟

㻔㼒㼛㼞㻌䃥㻤㻌㼜㼛㼟㼕㼠㼕㼛㼚㼕㼚㼓㻌㼜㼕㼚㼟㻕

(4箇所)
バネ座金

平座金

20

4-M8×40

Ｆ

Ｈ

Ｆ

Ｖ

Ｆ

Ｈ

Ｆ

Ｈ

Ｆ

Ｈ

Ｍ

Ｌ

Ｍ

Ｌ

Ｆ

Ｖ

Ｍ

Ｔ

(Four positions)

Spring washer

Plain washer

<Detail of installation dimension>

(Base section of a robot arm))

RH-3FH/6FH series

RH-12FH/20FH series

4-M8x40 (RH-3FH/6FH series)

4-M12x45 (RH-12FH/20FH series)

«
...
22
23
24
25
26
...
»

Содержание RH-12FH Series



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для RH-12FH Series

Бренд: DANLERS Страницы: 2

Бренд: Haas Automation Страницы: 26

Бренд: Teac Страницы: 44

Бренд: Te Pari Страницы: 6

Бренд: Yuwell Страницы: 2

Exitronix LEMD Series

Бренд: BARRON Страницы: 6

Бренд: Wayflex Страницы: 11

Бренд: Vectra Fitness Страницы: 18

Бренд: Santa Medical Страницы: 7

Бренд: dbx Страницы: 2

Бренд: Yuwell Страницы: 18

BIS U-4A7-082-01C-07-S4

Бренд: Balluff Страницы: 138

Megabar System EQLED63

Бренд: Equinox Systems Страницы: 12

Бренд: VISIO Страницы: 20

Bain-Mari 7478.0125

Бренд: CombiSteel Страницы: 47

Бренд: Midstream Страницы: 13

Бренд: Preventice Solutions Страницы: 8

Бренд: Sumitomo Drive Technologies Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды