Mitsubishi Electric Q06CCPU-V-H01 Скачать руководство пользователя страница 31

Страница: 31 / 38

5. External wiring

5.1 10BASE-T/100BASE-TX Connection

Sufficient safety precautions must be taken when installing the 100BASE-TX and
10BASE-T networks.
Consult a specialist when connecting cable terminals or installing trunk line
cables, etc.

(1) Twisted pair cable

Twisted pair cables are used for connection to 10BASE-T/100BASE-TX

interfaces.

Use the twisted pair cable that meets IEEE802.3 10BASE-T/100BASE-TX

standards.
(a) For 100Mbps

Either of the following 1) and 2) can be used.

1) Unshielded twisted pair cable (UTP cable), Category 5

2) Shielded twisted pair cable (STP cable), Category 5

(b) For 10Mbps

Either of the following 1) and 2) can be used.

1) Unshielded twisted pair cable (UTP cable), Category 3 (4, 5)

2) Shielded twisted pair cable (STP cable), Category 3 (4, 5)

POINT

During the high speed communication (100Mbps) via 100BASE-TX

connection, a communication error may occur due to high frequency noise

generated from the device other than C Controller module, depending on the

installation environment.

When configuring the network system, take the following measures on the C

Controller module side to eliminate the effect of high frequency noise.

1) Wiring

• Keep the twisted pair cables away from the main circuit or power cables.

• Make sure to place the twisted pair cables in a duct.

2) Cable

• In the environment where the cable is susceptible to noise, use the

shielded twisted pair cable (STP cable).

3) Retry processing

• In the environment where cables are susceptible to noise, include the retry

processing in the user program.

4) 10Mbps communication

• Connect the 10Mbps-compatible device to C Controller module, and then

transmit data at transmission speed of 10Mbps.

(2) Hub

The C Controller module discriminates between 10BASE-T and

100BASE-TX and between full-duplex and half-duplex communication

modes according to the hub.

When connecting to the hub that does not have the auto negotiation

function, set the hub to operate in the half-duplex communication mode.

Содержание Q06CCPU-V-H01







































Результаты поиска

Содержание Q06CCPU-V-H01

Отзывы:

Похожие инструкции для Q06CCPU-V-H01

Бренды по названию

Популярные бренды

Mitsubishi Electric Q06CCPU-V-H01, Руководство пользователя

Результаты поиска

Содержание Q06CCPU-V-H01

Отзывы:

Похожие инструкции для Q06CCPU-V-H01

Бренды по названию

Популярные бренды