Mitsubishi Electric PUHZ-W112VHA Скачать руководство пользователя страница 53

Страница: 53 / 58

OPERATING PROCEDURE

PHOTOS/FIGURES

4. Removing the thermistor <Plate HEX liquid> (TH6) and

thermistor <Ambient> (TH7)

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Disconnect the connectors, TH7/6 (red) on the controller

circuit board in the electrical parts box.

(4) Loosen the 2 wire clamps on top of the electrical parts

box. (TH7 only)

(5) Loosen the fastener for the lead wire on the controller

circuit board in the electrical parts box.

(6) Loosen the cable strap and wire clamp for the lead wire

on the bottom of electrical parts box. (TH6 only)

(7) Pull out the thermistor <Plate HEX liquid> (TH6) and

thermistor <Ambient> (TH7) from the sensor holder.

Note: In case of replacing thermistor <Plate HEX liquid>

(TH6) or thermistor <Ambient> (TH7), replace it

together.

Photo 6

Photo 5

<R2/R3 model only>

5. Removing the thermistor <Discharge> (TH4) and thermis-

tor <Comp. surface> (TH34)

(1) Remove the service panel. (See Photo 1)

(2) Disconnect the connector TH4 (white) on the controller

circuit board in the electrical parts box.

(3) Loosen the wire clamp on separator.

(4) Loosen the cable strap for the lead wire on the bottom of

electrical parts box. *

(5) Pull out the thermistor <Discharge> (TH4) from the sen-

sor holder.

[Removing the thermistor <Comp. surface> (TH34)]

(6) Remove the top damper, then pull out the thermistor

<Comp. surface> (TH34) from the holder of the compres-

sor shell.

TH3, TH4 and TH34 are fixed together with a cable tie.

When exchanging TH4 and TH34, cut the cable tie bundling

TH3, TH4 and TH34 to release the lead wires.

Photo 7

6. Removing the thermistor <Liquid> (TH3) and thermistor

<Suction> (TH33)

(1) Remove the service panel. (See Photo 1)

(2) Disconnect the connectors TH3 (white) and TH33 (yellow)

on the controller circuit board in the electrical parts box.

(3) Loosen the fastener for the lead wire on the controller

circuit board in the electrical parts box.

(4) Loosen the cable strap for the lead wire on the bottom of

electrical parts box. *

(5) Loosen the wire clamp and wire clip on separator.

(6) Pull out the thermistor <Liquid> (TH3), <Suction> (TH33)

from the sensor holder.

TH3, TH4 and TH34 are fixed together with a cable tie.

When exchanging TH4 and TH34, cut the cable tie bundling

TH3, TH4 and TH34 to release the lead wires.

Photo 8

4-way valve

Thermistor <Plate HEX liquid> (TH6)

Lead wire of

thermistor

(TH7)

Sensor holder

High pressure

sensor (63HS)

Stay

Compressor (MC)

Thermistor

(TH4)

Thermistor

<Comp. surface> (TH34)

Top damper

High pressure sensor (63HS)

Thermistor <Liquid> (TH3)

Compressor (MC)

Thermistor <Suction>

(TH33)

Low pressure switch (63L)

4-way valve

Low pressure

switch (63L)

Thermistor

<Plate HEX

liquid> (TH6)

OCH562D

Содержание PUHZ-W112VHA



























































Результаты поиска

Содержание PUHZ-W112VHA

Отзывы:

Похожие инструкции для PUHZ-W112VHA

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHZ-W112VHA, Руководство по обслуживанию

Результаты поиска

Содержание PUHZ-W112VHA

Отзывы:

Похожие инструкции для PUHZ-W112VHA

Бренды по названию

Популярные бренды