Mitsubishi Electric PUHZ-W112VHA Скачать руководство пользователя страница 27

Страница: 27 / 58

OCH562D

Check method of DC fan motor (fan motor/outdoor multi controller circuit board)

Notes

· High voltage is applied to the connector (CNF1, 2) for the fan motor. Pay attention to the service.

· Do not pull out the connector (CNF1, 2) for the motor with the power supply on.

(It may damage the outdoor controller circuit board and fan motor.)

Self check

Symptom: The outdoor fan cannot rotate.

Replace the outdoor controller

circuit board (C.B).

Disconnect the FAN motor connector

and measure the resistance of

connector pins. Refer to “8-4. HOW

TO CHECK THE PARTS”.

Correct the wiring.

Yes

Fail

Fuse check

Check the fuse (F5) on outdoor

controller circuit board.

Wiring contact check

Contact of fan motor connector

(CNF1,2)

Power supply check

Measure the voltage on the outdoor controller circuit board.

TEST POINT

: V

280–380 V DC (between 1 (+) and 4 (−) of CNF1,2)

TEST POINT

: V

15 V DC

(between 5 (+) and 4 (−) of CNF1,2)

Is the fuse normal?

Is the fan motor normal?

Is there contact failure?

Is the voltage normal?

Replace the defective fan motor.

Replace the outdoor

controller circuit board.

Check fan motor rotation.

Complete.

Replace the defective fan motor.

Replace the outdoor

controller circuit board.

Check fan motor rotation.

Replace the outdoor controller

circuit board (C.B) and the

defective fan motor.

Yes

Содержание PUHZ-W112VHA



























































Результаты поиска

Содержание PUHZ-W112VHA

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHZ-W112VHA, Руководство по обслуживанию

Результаты поиска

Содержание PUHZ-W112VHA

Отзывы:

Бренды по названию

Популярные бренды