Mitsubishi Electric PUHZ-W112VHA Скачать руководство пользователя страница 54

Страница: 54 / 58

OPERATING PROCEDURE

PHOTOS/FIGURES

7. Removing the 4-way valve coil (21S4), and linear expan-

sion valve coil (LEV-A, LEV-B)

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

[Removing the 4-way valve coil] (See Photo 9)

(3) Remove 4-way valve coil fixing screw (M4 × 6).

(4) Remove the 4-way valve coil by sliding the coil toward

you.

(5) Disconnect the connector 21S4 (green) on the controller

circuit board in the electrical parts box.

(6) Loosen the fastener, cable strap and wire clamp for the

lead wire on the electrical parts box and separator.

[Removing the LEV coil] (See Photo 10)

(3) Loosen the lead wires fixed to the pipes with bands.

(4) Remove the linear expansion valve coil by sliding the coil

upward.

(5) Disconnect the connectors, LEV-A (white) and LEV-B (red)

on the controller circuit board in the electrical parts box.

(6) Loosen the wire clip for the lead wire on the electrical

parts box.

Photo 9

8. Removing the 4-way valve

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove the electrical parts box. (See Photo 4)

(4) Remove the cover panel (front).(See Photo 1)

(5) Remove the stay.

(6) Remove the water pipes connected to water outlet and

water inlet.

(7)

Remove 5 side panel (R) fixing screws (5 × 12) (4: rear of

the unit/1: right side base) and remove the side panel (R).

(8) Recover refrigerant.

(9) Remove the welded part of 4-way valve.

Refer to the notes below.

Photo 10

<R2/R3 model only>

9. Removing LEV

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove the electrical parts box. (See Photo 4)

(4) Remove the cover panel (front). (See Photo 1)

(5) Remove the stay.

(6) Remove the water pipes connected to water outlet and

water inlet.

(7) Remove the side panel (R).

(8) Remove the LEV coil.

(9) Recover refrigerant.

(10) Remove the welded part of LEV.

Refer to the notes below.

Photo 11

Notes:

1. Recover refrigerant without spreading it in the air.

2. The welded part can be removed easily by removing the side panel (R).

3. When installing the following parts, cover it with a wet

cloth to prevent it from heating, then braze the pipes so

that the inside of pipes are not oxidized;

•

4-way valve (procedure 8), 120°C or more

• LEV (procedure 9), 120°C or more

• High pressure switch and low pressure switch

(procedure 10), 100°C or more

10. Removing the high pressure switch (63H) (See Photo 9)

and the low pressure switch (63L)

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove the electrical parts box.

(4) Remove the cover panel (front). (See Photo 1)

(5) Remove the stay.

(6) Remove the water pipes connected to water outlet and

water inlet.

(7) Remove the side panel (R).

(8) Recover refrigerant.

(9) Remove the welded part of high pressure switch and low

pressure switch.

Refer to the notes on the right.

•

LEV (LEV-A)

High pressure switch (63H)

4-way valve coil fi xing screw

4-way valve

LEV (LEV-B)

4-way valve

Heat exchanger

Low pressure switch (63L)

High pressure sensor (63HS)

LEV (LEV-A)

4-way valve

LEV (LEV-B)

OCH562D

Содержание PUHZ-W112VHA



























































Результаты поиска

Содержание PUHZ-W112VHA

Отзывы:

Похожие инструкции для PUHZ-W112VHA

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHZ-W112VHA, Руководство по обслуживанию

Результаты поиска

Содержание PUHZ-W112VHA

Отзывы:

Похожие инструкции для PUHZ-W112VHA

Бренды по названию

Популярные бренды