Mitsubishi Electric Mr.Slim MUZ-A17NA Скачать руководство пользователя страница 55

Страница: 55 / 84

MUZ-A09/12/15/17 MUY-A15/17

L Check of LEV (Expansion valve)

This figures show about MSZ-A09/12/15/17.

MUZ-A24 MUY-A24 MUZ-GA24 MUY-GA24

Press OPERATE/STOP (ON/OFF) button of the remote

controller (the set temperature is displayed) with the

remote controller headed towards the indoor unit. 1

Expansion valve operates in full-opening direction.

NOTE

: After check of LEV, do the undermentioned operations.

1. Turn OFF the power supply and turn ON again.

2. Press RESET button on the remote controller.

1. Regardless of normal or abnormal condition, a

short beep is emitted once the signal is received.

Measure each voltage between connector pins of

CN724 on the inverter P.C. board.

1. Pin (-) — Pin (+)

2. Pin (-) — Pin (+)

3. Pin (-) — Pin (+)

4. Pin (-) — Pin (+)

Is there about 3 - 5 VAC between each?

NOTE

: Measure the voltage with an analog tester.

Properly

x the LEV coil to the expansion valve.

Replace the inverter

P.C. board.

Replace the LEV coil.

Replace the expansion valve.

Is LEV coil properly

xed to

the expansion valve?

Does the resistance of LEV

coil have the characteristics?

(Refer to 10-4.)

Do you hear the expansion valve "click,

click·······"?

Do you feel the expansion valve vibrate

on touching it ?

Turn ON the power supply.

While pressing both OPERATION SELECT button

and TOO COOL button on the remote controller at the

same time, press RESET button.

First, release RESET button.

And release the other two buttons after all LCD in

operation display section of the remote controller is

displayed after 3 seconds.

Yes

Turn ON power supply to the outdoor unit after checking

LEV coil is mounted to the LEV body securely.

Is "click - click" sound heard?

Or, do you feel vibration of the LEV coil with a hand?

Disconnect the connector CN795.

Is there normal resistance to LEV coil?

Normal

Replace the outdoor electronic control P.C. board.

Replace the LEV coil.

Yes

Содержание Mr.Slim MUZ-A17NA





















































































Результаты поиска

Содержание Mr.Slim MUZ-A17NA

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric Mr.Slim MUZ-A17NA, Руководство по обслуживанию

Результаты поиска

Содержание Mr.Slim MUZ-A17NA

Отзывы:

Бренды по названию

Популярные бренды