Mitsubishi Electric Mr.Slim MUZ-A17NA Скачать руководство пользователя

Страница: 45 / 84

No.

Symptom

LED indication

Abnormal point/ Con-

dition

Condition Correspondence

LED1(Red) LED2(Yellow)

Outdoor unit

operates.

Once

Lighting

Primary current pro-

tection

The input current exceeds 15 A.

These symptoms do not mean any

abnormality of the product, but

check the following points.

• Check if indoor

lters are clogged.

• Check if refrigerant is short.

• Check if indoor/outdoor unit air

circulation is short cycled.

Secondary current pro-

tection

The current of the compressor exceeds 15 A.

Twice

Lighting

High-Pressure protec-

tion (MUZ)

The indoor gas pipe temperature exceeds 113°F (45°C) during

heating.

Defrosting in cooling

The indoor gas pipe temperature falls 37°F (3°C) or below dur-

ing cooling.

3 times

Lighting

Discharge temperature

protection

The discharge temperature exceeds 212°F (100°C) during op-

eration.

• Check refrigerant circuit and refrig-

erant amount.

• Refer to 10-5. "Check of LEV".

• Refer to 10-5. "Check of outdoor

thermistors".

4 times

Lighting

Low discharge tem-

perature protection

The frequency of the compressor is kept 80 Hz or more and

the discharge temperature is kept under 102°F (39°C) for more

than 20 minutes.

• Refer to 10-5. "Check of LEV".

• Check refrigerant circuit and refrig-

erant amount.

5 times

Lighting

Cooling high-pressure

protection

The outdoor heat exchanger temperature exceeds 136°F (58°

C) during operation.

This symptom does not mean any

abnormality of the product, but

check the following points.

• Check if indoor

lters are clogged.

• Check if refrigerant is short.

• Check if indoor/outdoor unit air

circulation is short cycled.

Outdoor unit

operates

9 times

Lighting Inverter check mode The unit is operated with emergency operation switch.

—

Lighting Lighting Normal

—

Содержание Mr.Slim MUZ-A17NA





















































































Результаты поиска

Содержание Mr.Slim MUZ-A17NA

Отзывы:

Похожие инструкции для Mr.Slim MUZ-A17NA

Бренды по названию

Популярные бренды

Mitsubishi Electric Mr.Slim MUZ-A17NA, Руководство по обслуживанию

Результаты поиска

Содержание Mr.Slim MUZ-A17NA

Отзывы:

Похожие инструкции для Mr.Slim MUZ-A17NA

Бренды по названию

Популярные бренды