Mitsubishi Electric FR-A8NP Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 92

background image

TROUBLESHOOTING

89

9

0.00

OFF

The network
is unstable.

The network setting is incorrect.

Check the network setting with the PROFIBUS-DP
network configuration software.

The inverter is affected by the
other nodes.

Check if any network error has occurred in the other
nodes.

No master is present in the network, or the master
is not properly operating.

Check the connection and the operation of the
PROFIBUS-DP master.

Red (ON)

The PROFIBUS communication had been
established (the green LED had been ON), but
the master stopped transmitting data to the option
unit during an inverter stop.

Check the master ladder, etc., and remove the causes
that disconnect the data transmission between the
master and the option unit.

E.OP1

Red (ON)

A communication cable break occurred after the
PROFIBUS communication had been established
(green LED had been ON).

Check the connection and the wiring of the
communication cable.

Communication errors occurred consecutively
after the PROFIBUS communication had been
established (green LED had been ON).

Connect a terminating resistor. If a terminating resistor
has been already connected, check if it is connected
properly.

The PROFIBUS communication had been
established (the green LED had been ON), but
the master stopped transmitting data to the option
unit during an inverter operation.

Check the master ladder, etc., and remove the causes
that disconnect the data transmission between the
master and the option unit.

Operation

panel display

on the inverter

LED on

FR-A8NP

Possible cause

Checkpoint / troubleshooting

«
...
88
89
90
91
92
»

Содержание FR-A8NP





























































































Отзывы:

Нет отзывов

Похожие инструкции для FR-A8NP

Бренд: FrSky Страницы: 2

Бренд: C3 Custom Coolers Страницы: 16

Бренд: Taie Страницы: 28

Бренд: jcm-tech Страницы: 8

Бренд: Paradox Страницы: 32

TEMP2000 Series

Бренд: Samwontech Страницы: 91

Бренд: Warren rupp Страницы: 18

Бренд: Yamaha Страницы: 100

Бренд: Bardiani Страницы: 96

Бренд: Eaton Страницы: 4

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 340

Бренд: ETC Страницы: 8

Бренд: Westfalia Страницы: 18

Бренд: Nibe Страницы: 92

Бренд: AUMA Страницы: 168

Бренд: SFC Страницы: 48

Бренд: Satel Страницы: 8

Бренд: M-system Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды