Mitsubishi Electric EMU4-D65, Инструкция по эксплуатации

Страница: 8 / 16

- 8 -
Screen Operation Note
12-17.
（
1
）
Push the ▲ ▼
＋ －
key, and change the scalling upper limit, lower
limit, and unit.
（
2
）
Push the / Phase key, and confirm the setting value.
（
3
）
12-1 will be displayed.
[Upp]
：
-32767
～
32767
（
4095
）
[Low]
：
-32767
～
32767
（
0
）
[Unit]
：
Non
⇔ A ⇔ mA ⇔ kA ⇔ V ⇔ kV ⇔ W ⇔ kW ⇔ MW ⇔ Hz ⇔ N ⇔
kN ⇔ Pa ⇔ kPa ⇔ MPa ⇔ C ⇔ deg ⇔ % ⇔
13 Setup the Number Limit
（
EMU4-AX4 only
）
13-1.
（
1
）
In 13-1, push the ▲ or ▼ key, and move the cursor to the
“12 Num.Limit”.
（
2
）
Push the / Phase key.
（
3
）
13.1-1 will be displayed.
Num.Limit
…Set any limint .
*If the scaling value over the limit, Number Limit
countup.
13.1 Setup the Limit A, Limit B, Limit C, and Limit D
（
EMU4-AX4 only
）
13.1-1.
（
1
）
In 13.1-1, push the ▲ or ▼ key, and move the cursor to the
“1 Limit A”.
（
2
）
Push the / Phase key.
（
3
）
13.1-2 will be displayed.
Limit B, Limit C, and Limit D is done in the same way
as the setting of Limit A.
13.1-2.
（
1
）
Push the ▲ ▼
＋ －
key, and change the set value.
（
2
）
Push the / Phase key.
（
3
）
13.1-3 will be displayed.
Limit…Set any scalling value.
You can configure the four different limits for
limit A, limit B, limit C, and limit D.
[Limit A]
：
Scaling Low
～
Scaling Upp
*If scaling setting value is set “Scaling Low > Scaling
Upp”, default setting is Scaling Upp.
13.1-3.
（
1
）
Push the ▲ ▼
＋ －
key, and change the set value.
（
2
）
Push the / Phase key.
（
3
）
13.1-4 will be displayed.
13.1-4
（
1
）
Push the ▲ ▼
＋ －
key, and change the set value.
（
2
）
Push the / Phase key.
（
3
）
13.1-5 will be displayed.
13.1-5
（
1
）
Push the ▲ ▼
＋ －
key, and change the set value.
（
2
）
Push the / Phase key.
（
3
）
13.1-1 will be displayed.
13.2 Setup the multiplying factor
（
EMU4-AX4 only
）
13.2-1.
（
1
）
In 13.2-1, push the ▲ or ▼ key, and move the cursor to the
“5 Factor”.
（
2
）
Push the / Phase key.
（
3
）
13.2-2 will be displayed.
13.2-2.
（
1
）
Push the
＋
or
－
key, and select the multiplying factor displayed.
（
2
）
Push the / Phase key.
（
3
）
13.2-3 will be displayed.
[Factor]
：
x1
⇔
x10
⇔
x100
⇔
x1000
⇔
Factor…Set up the multiplying factor displayed of
Number Limit.
13.2-3.
（
1
）
Push the
＋
or
－
key, and select the multiplying factor displayed.
（
2
）
Push the / Phase key.
（
3
）
13.2-4 will be displayed.
13.2-4
（
1
）
Push the
＋
or
－
key, and select the multiplying factor displayed.
（
2
）
Push the / Phase key.
（
3
）
13.2-5 will be displayed.
13.2-5
（
1
）
Push the
＋
or
－
key, and select the multiplying factor displayed.
（
2
）
Push the / Phase key.
（
3
）
13.2-1 will be displayed.
14 Save the settings
14-1.
14-2.
（
1
）
After setting all of the items, and push the Setup key.
（
2
）
14-1 will be displayed.
（
3
）
When save the settings, push the ▲ or ▼ key, move the cursor to
the “1 Save”, and push the / Phase key.
（
4
）
After completing the settings saving, 14-2 will be displayed.
Push the /Phase key.
（
5
）
Return to the operation mode.
1 Save → Save settings and return to
the operation mode.
2 Not Save → Discard the changes and
return to the operation mode.
3 Cancel → Continue the setup.
*Setting for condition of the measurement mode can only configure in the display unit is set to master.
（
Setting for condition of the measurement mode can not configure in
the display unit is set to slave.
）
*If you change a settings, please push the / Phase key and be sure to determine changes. If without determine, the changes will be discarded.
*The underline means the default of setting. After you have been set, even if a power failure occurs does not disappear setting.
*If you want to set the other circuit, push the Circuit key on the "Setup" screen (1-1), select the circuit, make the setting.
*Same voltage system is same setting in wire system, primary voltage, 2 circuits Measuring existence, Simple measurement.
7.2.2 Input/Output setup
－
the settings for the external Input/Output. EMU4-LG1-MB is not set.
Screen Operation Note
1 Transit to the Setup mode
1-1.
（
1
）
Push the Setup key in operation mode.
（
2
）
1-1 will be displayed.
（
1
）
Push the ▲ or ▼ key, and move the cursor to the ”2 I/O”.
Push the / Phase key.
（
2
）
2-1 will be displayed.
[Setup]
1 Measure
2 I/O
3 COM.
[Scaling]
Upp.: 04095
Low.: 00000
Unit:Non [4]
Quit Setup
1 Save
2 Not Save
3 Cancel
Completed
OK
[Measure]
10DIF.CONV.
11AD CONV.
12 Num.Limit
[Limit A]
- 32767
[1]
[Limit A]
- 32767
[2]
[Limit A]
- 32767
[3]
[Limit A]
- 32767
[4]
[Num.Limit]
3 Limit C
4 Limit D
5 Factor
[Factor]
x1
[1]
[Factor]
x1
[2]
[Factor]
x1
[3]
[Factor]
x1
[4]
[Num.Limit]
1 Limit A
2 Limit B
3 Limit C