Mitsubishi Electric EMU4-D65, Инструкция по эксплуатации

Страница: 6 / 16

- 6 -
Screen Operation Note
7(2) Setup the demand time
（
EMU4-LG1-MB
）
7(2)-1
（
1
）
In 7(2)-1, push the
▲
or
▼
key, and move the cursor to
the “6 Demand”.
（
2
）
Push the / Phase key and
（
3
）
7(2)-2 will be displayed.
[Demand]
：
0sec
⇔
5min
⇔
6min
⇔
7min
⇔
8min
⇔
9min
⇔
10min
⇔
11min
⇔
12min
⇔
13min
⇔
14min
⇔
15min
⇔
20min
⇔
25min
⇔
30min
⇔
7(2)-2
（
1
）
Push the
＋
or
－
key, and change the Io/Ior demand time value.
（
2
）
Push the / Phase key, and confirm the setting value.
（
3
）
7(2)-1 will be displayed.
8 Setup the electric energy equivalent rate
（
All models except for EMU4-LG1-MB
）
8-1.
（
1
）
In 8-1, push the ▲ or ▼ key, and move the cursor to the
“7 CONV.Wh”
（
2
）
Push the / Phase key.
（
3
）
8-2 will be displayed.
8-2.
（
1
）
Push the ▲ ▼
＋ －
key, and change the
“
CONV.Rate
”
value and
unit.
（
2
）
Push the / Phase key , and confirm the setting value.
（
3
）
Transition to the following screen by the setting wiring type.
2 circuit measurement → To 8-3
non-2 circuit measurement → To 8-1
[CONV.Rate]
：
0.001
～
10000
（
1.000
）
[Unit]
：
Non
⇔ Ｗｈ ⇔ ｋＷｈ ⇔ ＭＷｈ ⇔ Ｊ ⇔ ｍ
2
⇔ ｍ
3
⇔ Ｌ ⇔
ｋＬ ⇔
sec
⇔
min
⇔
hour
⇔ piece ⇔ set ⇔ ｇ ⇔ ｋｇ ⇔
ｔ ⇔ ￥ ⇔ ＄ ⇔
8-3.
（
1
）
In a similar way as 8-2, change the
“
CONV.Rate
”
value and unit of the
second circuit.
（
2
）
Push the / Phase key, and confirm the setting value.
（
3
）
8-1 will be displayed.
9 Setup the current cut-off rate (All models except for EMU4-LG1-MB, EMU4-PX4 and EMU4-AX4)
9-1.
（
1
）
In 9-1
，
push the ▲ or ▼ key , and move the cursor to the
“8 A Cut-off”.
（
2
）
Push the / Phase key.
（
3
）
9-2 will be displayed.
9-2.
（
1
）
Push the
＋
or
－
key, and change the set value.
（
2
）
Push the / Phase key , and confirm the setting value.
（
3
）
Transition to the following screen by the setting wiring type.
2 circuit measurement → To 9-3
non-2 circuit measurement → To 9-1
[A Cut-off]
：
0.1
～
50.0%
（
0.5
）
A cut-off rate…represent as the ratio of cut-off current
to rated current.
※
Measured value is 0A if it is less than the
cut-off current.
9-3.
（
1
）
In a similar way as 9-2, change the
“
A Cut-off
”
value of the second circuit.
（
2
）
Push the / Phase key, and confirm the setting value.
（
3
）
9-1 will be displayed.
10 Setup the Simple measurement
（
All models except for EMU4-LG1-MB, EMU4-PX4 and EMU4-AX4
）
10-1.
（
1
）
In 10-1, push the ▲ or ▼ key, and move the cursor to the
“9 SimpleMEA”.
（
2
）
Push the / Phase key.
（
3
）
10-2 will be displayed.
10-2.
（
1
）
Push the
＋
or
－
key, and select SimpleMEA ([On]
／
[Off]).
（
2
）
Push the / Phase key, and confirm the setting value.
（
3
）
Transition to the following screen by the setting SimpleMEA
（
[On]
／
[Off]
）
[On] setting
→ To 10-3
[Off] setting
→ To 10-1
[SimpleMEA]
：
Off
⇔
On
⇔
SimpleMEA…The value set in the electric power and
the power factor as the fixed value.
By measuring the current only, and
calculating the values of the measurement
elements.
10-3.
（
1
）
Push the
▲ ▼
＋ －
key, and change the power factor value
In the SimpleMEA.
（
2
）
Push the / Phase key,and confirm the setting value.
（
3
）
Transition to the following screen by the setting wiring type.
2 circuit measurement → To 10-4
non-2 circuit measurement → To 10-1
[FP Set]
：
-0.001
～
1.000
～
0.000
10-4.
（
1
）
In a similar way as 10-3, change the power factor value of the second circuit.
（
2
）
Push the / Phase key, and confirm the setting value.
（
3
）
10-1 will be displayed.
11 Setup the Ior difference conversion
（
EMU4-LG1-MB only
）
11-1.
（
1
）
In 11-1, push the ▲ or ▼ key , and move the cursor to the
“
10 DIF.CONV
”
.
（
2
）
Push the / Phase key.
（
3
）
11-2 will be displayed.
[DIF.CONV]
：
Off
⇔
On
⇔
DIF.CONV…To calculate the amount of change from
the Ior difference converted value.
11-2.
（
1
）
Push the
＋
or
－
key, and select the Ior difference converted value
（
[On]
／
[Off]
）
（
2
）
Push the / Phase key, and confirm the setting value.
（
3
）
Transition to the following screen by the setting DIF.CONV
（
[On]
／
[Off]
）
.
[On] setting
→ To 11-3
[Off] setting
→ To 11-1
[Measure]
5 MEA.Mode
6 Demand
7 CONV.Wh
[CONV.Rate]
1 .000
[Unit]
Non [1]
[CONV.Rate]
1 .000
[Unit]
Non [2]
[Measure]
7 CONV.Wh
8 A Cut-off
9 SimpleMEA
[SimpleMEA]
Off
[FP Set]
1.000
[1]
[FP Set]
1.000
[2]
[Measure]
6 Demand
7 CONV.Wh
8 A Cut-off
[DIF.CONV ]
Off
[Measure]
8 A Cut-off
9 SimpleMEA
10 DIF.CONV
[A Cut-off]
0 0.5
％
[1]
[A Cut-off]
[2]
[Measure]
4 DISP.Mode
5 MEA.Mode
6 Demand
[Demand]
Io/Ior
：
5min
0 0.5
％