Mitsubishi Electric AnyWire ASLINK Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 200

background image

APPX

Appendix 2 Remote Register

143

A

Latest alarm ID storage area

■

Device No.

■

Description

This area stores the ID of the slave module that was the target of the latest alarm code when an alarm occurs.
However, 0FFFH is stored when the following alarm occurs.
• DP/DN short error (alarm code: 0CC9H)
• 24V/DP short error (alarm code: 0CCBH)
• Parameter access target module ID error (alarm code: 0D2EH)
• AnyWireASLINK transmission function execution error (alarm code: 0D40H)
• Easy replacement error for one slave module (Parameter access error) (alarm code: 0D82H)
• Non-compatible slave module connection error (alarm code: 0D83H)
• Compatibility inspection error (Excess number of connected slave modules error) (Alarm code: 0D85H)
• Compatibility inspection error (Word data usage setting) (alarm code: 0D86H)
• New ID error (alarm code: 0D92H)
• Excess number of connected slave modules error (alarm code: 0D93H)
The IDs relevant to alarm occurrence are stored in the alarm ID information storage area below.



Page 166 Alarm ID information storage area

After eliminating the cause of the alarm that occurred, turn on Error reset request flag (RY0) to clear the alarm ID.

Number of the IDs of the disconnected modules

■

Device No.

■

Description

This area stores the number of slave module IDs that send no response due to disconnection of the transmission cable (DP,
DN) or a failure in the slave module alone among the IDs of the connected modules. (Up to 256)
If the disconnection error automatic recovery function is enabled, the number of slave modules (number of disconnected
module IDs) from which errors are cleared automatically decreases.
After automatic address detection, the data are updated as soon as a response error is detected.
For details on the disconnected module IDs, refer to the disconnected module ID information storage area below.



Page 165 Disconnected module ID information storage area

Name

Device No.

Latest alarm ID storage area

RWr3

Name

Device No.

Number of the IDs of the disconnected modules

RWr6

«
...
143
144
145
146
147
...
»

Содержание AnyWire ASLINK









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AnyWire ASLINK

Бренд: XBOX Страницы: 4

Бренд: Galcon Страницы: 32

Бренд: J3C Страницы: 2

Flashlight Blue

Бренд: Hama Страницы: 10

Бренд: Hama Страницы: 4

Бренд: Hama Страницы: 14

Бренд: Hama Страницы: 5

Frigolink FVB110B

Бренд: WURM Страницы: 4

MicroTech II UV05

Бренд: AAF Страницы: 50

JetWeb JX2-PRN1

Бренд: Jetter Страницы: 25

Бренд: Danfoss Страницы: 16

Consolidated 2900-40 Series

Бренд: Baker Hughes Страницы: 80

Бренд: W.E.ST. Страницы: 34

Бренд: Ltech Страницы: 4

Бренд: Motor Guard Страницы: 2

Бренд: K&K Страницы: 6

Optidrive Elevator

Бренд: Invertek Страницы: 5

Бренд: Techtrol Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды