Mitsubishi Electric AnyWire ASLINK Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 200

Mitsubishi Electric AnyWire ASLINK Скачать руководство пользователя страница 81

7 FUNCTIONS

7.13 AnyWireASLINK Version Compatibility Inspection Function

79

7

How to check the error status

If an AnyWireASLINK version compatibility inspection error exists after the inspection, the status will be as follows.

The following are the probable causes of the AnyWireASLINK version compatibility inspection error. Identify the error cause
and take appropriate actions.
• A slave module not supporting word data is connected to the NZ2AW1GNAL.
• The number of connected slave modules exceeds the maximum number of connectable modules.
• Parameter access failed on one or more slave modules.
Clear the AnyWireASLINK version compatibility inspection error, and start the inspection again.

Precautions

• Even when the AnyWireASLINK version compatibility inspection is executed, the configuration information of the slave

modules that is saved in the NZ2AW1GNAL is not updated.

• When an ASLINK version compatibility check is executed, the error information and alarm information are cleared. The

signal to be cleared is the same as below.



Page 137 Error reset request flag

Item

Description

AnyWireASLINK version compatibility inspection error flag
(RX8)

Turns on.

Latest alarm code storage area (RWr2)

The relevant alarm code is stored.
The alarm codes that may occur are listed below.

• Non-compatible slave module connection error (alarm code: 0D83H)
• Compatibility inspection error (Parameter access error) (alarm code: 0D84H)
• Compatibility inspection error (Excess number of connected slave modules error) (Alarm code:

0D85H)

• Compatibility inspection error (Word data usage setting) (alarm code: 0D86H)

Latest alarm ID storage area (RWr3)

The ID of the slave module where the following alarm has occurred is stored.

• Compatibility inspection error (Parameter access error) (alarm code: 0D84H)

For the following alarms 0FFFH is stored.

• Non-compatible slave module connection error (alarm code: 0D83H)
• Compatibility inspection error (Excess number of connected slave modules error) (Alarm code:

0D85H)

• Compatibility inspection error (Word data usage setting) (alarm code: 0D86H)

Version compatibility inspection error ID area (5700H to
577FH)

ID information is registered.

ALM LED

Turns on.

«
...
79
80
81
82
83
...
»

Содержание AnyWire ASLINK









































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды