Mitel MiVoice 5340e Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 97

background image

5330e/5340e IP Phones – User Guide

Handset Alerting Tones and LEDs

The handset provides the following alerting tones:

Feature

Function

Mute

key on cordless device

ON/OFF

2-pitch tone occurs immediately. Reminder tone occurs 30
seconds after activation and then regularly until deactivated.

Mute

key on Phone ON/OFF

Immediate tone with Bluetooth; no immediate tone with DECT.
Reminder tone occurs 30 seconds after activation and then
regularly until deactivated.

Low battery (within 10 minutes left
for DECT and within 20 minutes left
for Bluetooth)

3 beeps and 20 second pause repeated 3 times

Low battery (within 2 minutes left)

3 rapid beeps and 1.5 second pause repeated 3 times

Out of range

DECT:

Repetitive 3-pitch tone until you are back in range.

Note

: If you are out of range for more than 10 seconds, any call

that is in progress is dropped and not recovered.

Bluetooth:

Single 3-pitch tone to indicate that you are out of

range.

Note

: All Bluetooth devices will drop any call in progress

if the maximum range is exceeded.

Note

: Audio indications are heard in the handset only when it is in use and may interrupt

voice transmission.

The handset has two LEDs:



Blue – indicates the operational status of the handset



Green – indicates the status of the electrical charge of the battery

LED

Color

LED State

Indicates

Solid

Handset is muted

Blinking

Handset is in pairing mode

Winking

Active audio path between Handset and Module

Blue

Off

No audio path between Handset and Module OR

Battery is dead

Solid

Battery is fully charged

Blinking

Battery is charging.

Note

: It is normal for the handset LED to cycle

between blinking and solid as battery charge is maintained.

Green

Off

When handset is cradled and the LED does not flash or illuminate, this
indicates an absence of battery power. During the first 30 – 60 minutes
that the light is off, the battery may be trickle charging. If that is the
case, the LED will resume normal behavior within that 60 minute period.
If the LED remains off for more than 60 minutes, then either the battery
is no longer chargeable or there is a problem in the charging circuit.

Blinking: LED is On and Off for equal amount of time
Winking: LED is On for a short period of time and Off for a longer period

- 79 -

«
...
85
86
87
88
89
...
»

Содержание MiVoice 5340e


































































































Отзывы:

Нет отзывов

Похожие инструкции для MiVoice 5340e

Бренд: Panasonic Страницы: 48

EasyFlip OLT2908

Бренд: Olitech Страницы: 57

Бренд: Palm Страницы: 2

Бренд: Palm Страницы: 60

Бренд: Palm Страницы: 130

Бренд: Palm Страницы: 6

Бренд: Palm Страницы: 28

Бренд: palmOne Страницы: 2

700wx - Treo Smartphone 60 MB

Бренд: Palm Страницы: 288

Бренд: PalmMicro Страницы: 19

Бренд: Palm Страницы: 16

Бренд: Tadiran Telecom Страницы: 253

Бренд: OUKITEL Страницы: 62

Бренд: Hanlong Страницы: 2

PHONEEASY 410S gsm

Бренд: Doro Страницы: 140

A99-WMTA3030-01

Бренд: Westell Страницы: 12

2 VOICE 1083/58

Бренд: urmet domus Страницы: 60

Бренд: Uplink Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды