*1:
Depending on the emulation selected, the following set
>Code sets
are available.
*2:
The printer can be set to print error data during KPDL emula-
tion. If this is set to
On
, error data will be printed if trouble
occurs during printing. This is set to
Off
before leaving the
factory.
*3:
You can select either Courier or Letter Gothic. Any font can
be selected as
Dark
or
Regular
. These fonts are dis-
played when the Font menu is Internal.
*4:
The
>Size
menu is not available for the Courier and Let-
ter-Gothic fonts. The
>Pitch
menu is displayed instead
for these fixed width fonts.
*5:
Although
Auto
is the default setting and this menu does
not usually appear, page protection mode will be forcibly set
to on if a
Print overrun Press CONTINUE
error occurs due to insufficient printer memory. Be sure to
return this setting to
Auto
in order to maintain high printer
memory efficiency.
*6:
Turning this to
ON
increases the maximum number of char-
acters that can be printed in a line for an A4 page (78 char-
acters at 10 pitch) and likewise increases the maximum per
line on Letter size paper (80 characters at 10 pitch).(Only PCL
6 emulation)
*7:
This sets the resolution for printing. For 1200 dpi there are
two modes. In Fast 1200 mode, printing is equal to 1200 dpi
(1200 dpi horizontal × 600 dpi vertical) comparatively, Fine
1200 mode is slower, but in Fine 1200 mode true1200 dpi
printing is facilitated. The printing is slower than Fast mode
but the print quality is better.
*8:
This is displayed only after the DP-1400 memory has been
expanded. (The total must be 12 MB or more)
*9:
This is displayed when the size dial on the paper cassette is
set to Custom. (See section
2.7. Setting Custom Sizes
.)
*10:
This sets whether to enable or disable the difference between
A4 size and letter size. Under the default setting of
Off
, the
paper size of the paper source is matched to the paper size
given for the data, and if these differ a corresponding error
message is displayed. When this is set to
On
, printing is per-
formed even if the actual paper size differs from the paper
size given for the data.
*11:
This menu is displayed only when
Custom #
is selected.
*12:
After the printer accepts all data and there is no more data
from the computer, the printer will wait a set amount of time
without printing the final page. Once this preset amount of
time has elapsed, the printer will automatically issue a form
feed. This timeout setting can be set in 5-second increments
up to 495 seconds.
*13:
This is the total number of pages printed by the printer up to
the present time.
*14:
These menus are for service personnel.
They should not be operated by the user.
>Resource prot.
Perm / Temp
Continued from Previous page
Others >
>Form Feed
Time Out 030 sec.
>MSG language
English
(*12)
>Sleep timer
030 min.
>Print HEX-DUMP
>Printer Reset
>Number of pages
printed 0123456
>Resource prot.
Permanent
>Resource prot.
Off
>Buzzer
Off
>Buzzer
On
>Service >
>>Developer
>>Print
Status Page
>>Drum
(*14)
(*13)
Содержание DP-1400
